background image

8

© 2018 Monte Carlo Fan Company

10/2018

REMOTE CONTROL SETTING and OPERATION

Universal Mode and Learning Mode

There are “Universal Mode” and “Learning Mode” with the remote controller. 
If choosing “

Universal Mode

”, simply place dip (code) switch at UPPER 

position. Your fan with the remote controller is ready to use. 

Note

: If using universal mode, your fan can be controlled with other remote 

transmitters with the same setting.
To control the fan with specific remote transmitter, choose “

Learning Mode

” 

by placing the dip (code) switch at LOWER position and then make learn 

function setting as below. 

Learn function setting

, Restore power source to your fan, press and hold 

the “

LEARN

” button for at least 3 seconds. You must press the “

LEARN

” 

button within 60 seconds of restoring power to the fan.

Note

: If the power is on already, you must turn the power off for 10 seconds 

at least, and then turn the power back for remote control learn function 

setting. 

Note

: If the fan is installed with light, light will twinkle 2 times. The remote 

control setting process is complete and your fan is ready for use. For fans 

without light, check operation using remote transmitter. 

Note

: If you want to control the fan with another transmitter, make the same 

setting. A fan can be controlled by 2 transmitters maximum.

Transmitter Operation  

Remove the battery cover from the remote control transmitter and install 

battery, battery provided. Replace the cover.

Note

: Use 2 1.5V/AAA 

 

battery. 

Note

: If not using for long period of time, remove battery to prevent damage 

to remote transmitter, and store the remote transmitter away from excess 

heat or humidity.

ON

DIM

LE

AR

N

L.CODE

COMMON

CODE

L.CODE

COMMON

CODE

ON

DIM

Universal Mold 

Learning Mold

Dimming / Non Dimming Setting

The “DIM” selection is the light dimmable selection and the light will cycle 

from bright to dim to bright until button is released. The “ON” selection is the 

light ON/OFF only (non dimming function). Light will maintain last setting if 

turned off.

Note

: The remote controller is set with dimming function at factory,

 

Note

: If the remote receiver has been wired with fan, turn power off by wall 

switch before switch “DIM” and “ON/OFF” selection.  

Dimming/

Non dimming

LEARN

Learn

The receiver provides the following protective functions

Lock protection- The DC motor has a build-in safety feature against blade or motor obstruction during operation. If 

something obstructs the fan blades or motor, the motor will keep trying to run for 5 times and then stop operation 

after about 60 seconds of interruption. Please remove obstacles and reset. To reset it by turn the fan off by remote 

transmitter and then turn the fan on, Or you may turn power off for 15 seconds then turn power back, and then turn 

the fan on,    

Over load protection (current limit)- The device will limits the maximum current output from the receiver/drive when the 

fan or light load was increased abnormally. 

Содержание 3AMR60












Отзывы: