MONTAGUE SBE3418 Скачать руководство пользователя страница 10

10 

 

MAINTENANCE 

MAINTENANCE AND SERVICING INSTRUCTIONS 
 

Regular servicing by a competent person is recommended to ensure the continued safe and      
efficient performance of the appliance. 
 
A list of Authorized Service Agents can be obtained from our Service Department at the following 
address: 

 

FRIALATOR INTERNATIONAL, LTD. 

4, HEATON COURT, OFF RISLEY ROAD 

BIRCHWOOD, WARRINGTON, WA3 6QU 

Telephone: (01925) 821280 

Fax: (01925) 815653 

 

 

 

        WARNING: 

Turn off the gas supply to the appliance at the service cock before        

 

 

 

       commencing any servicing work. 

 

IMPORTANT:

 

Test for gas soundness on completion of any servicing work. 

 

 
GAS TAPS 

 
Re-greasing of the taps is not recommended. If the tap spindles become seized or difficult to turn, 
refer to the Replacement of Parts section in this manual. 

 
CLEANING BURNER HEAD 

 
1.  Remove top panel. 
 
2.  Remove top liner panel with insulation. 
 
3.  Remove ceramic radiants from the burner frame assembly. 
 
4.  Remove screw from left end of burner head. 
 
5,   Loosen thumb screw holding burner venturi in place. 
 
6.  Remove burner head. 
 
7.  Clean the burner with a stiff scrubbing brush and shake well to ensure that the ports are clear. 
 
8.  Reassemble in the reverse order.  

MAINTENANCE 

Содержание SBE3418















Отзывы: