background image

Reference 09Aug2014 – V16

 

Pg 

7 of 12

 

Copyright 2002-2014, Monster Tower, Inc.

 

shows the side view with the tower at ideal front to rear leg-mounting distances.  

Measure from the rear leg to the approximate location where the front base will be 

mounted to confirm they will be in the acceptable range before continuing. 

    

Tighten the bolts at the top of the rear legs and the setscrews in the top section to make 

it easier to handle the tower during the final steps. 

 

An optional step at this point is to attach the front legs to the top section to make sure 

they do not interfere with the windshield opening, or any other unforeseen obstructions. 

To attach the front legs, assemble a base to each of the front legs (base assembly view) 

and attach the front legs to the top section. Do this using item 16 to attach the Heim joint 

to the base, and Item 6 to attach the leg swivel (part 11) to the front top section swivel 

(part 8). You can then determine the final location of all four bases by placing the tower 

into its final position. This will be easier if you can hang the tower from a tree, rafter or 

have a few friends help you hold the tower in place. 

 

Mark the location of the front bases and measure from a front base to a reference 

location on the boat, as well as from the front base to the rear base to make sure they 

are positioned the same on both sides of the boat.  

 

You are now ready to attach the rear bases to the boat, so you will need to detach them 

from the legs and take the base assemblies apart. If you have the front legs attached to 

the top section you will want to detach them as well. 

 

Attaching the bases to the deck of the boat 

 

Take a few minutes to double check the dimensions between the base locations and 

several reference points on your boat to make sure they are in the same locations on 

each side (measure twice, drill once). Check underneath the deck to make sure there 

are no wires or obstructions as well as good places for the backing plate. For each rear 

base, mark the location to drill the two holes through the deck as in the following picture. 

The masking tape makes it easy to accurately mark the holes. To make drilling easier 

we recommend center punching the marks so the drill bit does not wander when drilling. 

 

 

 

 

Содержание MT1













Отзывы: