*The finished and rough-in dimensions are determined by the type
of installation being made. The finished cutout width includes side
panel thicknesses. See “Side Panel or Filler Options.”
*41 1/2" - 43 1/2"
7"
Wall View
(not to Scale)
Locate Grounded
Electrical outlet
Within Solid
Area Above
84 1/2" max
83" min
Finished
Rough
Opening
74"
From Floor to
Bottom of
Electrical Area
5"
18 3/8"
5"
3 1/2"
5"
3 1/2"
Locate Water
Supply Within
the Shaded
Area Below
10
Side View
(not to scale)
24 3/4"
4"
Front View
(not to scale)
42" Overall Width
41" Case Width
12 1/4" max
10-3/4" min
84 1/2" max
83" min
72 1/4"
ZISW42DY (white dispenser)
ZISB42DY (black dispenser)
42" Built-In Refrigerator
Design Information
Designed to be installed flush with surrounding cabinetry.
Cutout dimensions, clearances and side panel sizes are
determined by the many installation options available. Side
panels must be used whenever the sides of the refrigerator
will be exposed. If custom enclosure has been made and
installed, or if you are installing between pantry and oven
cabinets, side panels are not required unless you are using
frameless cabinets. IMPORTANT–Side panels, 1/2" min.
thick, are required for FRAMELESS CABINETS.
• Field installed custom panels, Lexan
or stainless steel
panels are required. Custom door panels and grille panel
sizes vary to accommodate the kit being used.
• A custom toekick can be installed to match or comple-
ment the surrounding cabinetry. A standard toekick is
supplied. For a custom toekick, use supplied toekick as a
template to cut notches for hinges and water lines.
Optional Kits:
• ZWBP42D: Black Lexan
Panel Kit (no trim kit required).
• ZWWP42D: White Lexan
Panel Kit (no trim kit required).
• ZWSP42D: Stainless Steel Panel Kit (no trim kit required).
• ZKH1: Provides for the installation of a custom handle on
1/4" custom panels.
• ZG1: Provides 1/4" grille panel frame side pieces for 83",
83-1/2" and 84-1/2" installation heights. Factory set height
is 84".
• ZKT42: Provides for the installation of 3/4" custom door
and grille panels.
• ZKHT1: Provides for the installation of a custom handle
using 3/4" door and grille panels. (This kit must be used in
conjunction with ZKT42.)
• ZWCD1: Provides for the installation of a custom collar
trim on the dispenser for one continuous custom panel
on the freezer door. This kit can be used alone, or with
one or more trim kits.
Additional Specifications
• A 115 volt 60 Hz., 15 or 20 amp power supply is required.
An individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall.
• Water line can enter opening through the floor or back
wall. The water line should be 1/4" O.D. copper tubing
between the cold water line and water connection
location, long enough to extend to the front of the
refrigerator. Installation of an easily accessible shut off
valve in the water line is recommended.
Clearances
If the refrigerator is to be installed in a corner:
• A 2" min. clearance between the case trim and adjacent
wall on both sides of the refrigerator will assure a 90
°
door opening and access to all drawers. An 8" clearance
is required on both sides for removal of pans.
Monogram
Dimensions &
Specifications
CUSTOM PANEL
DIMENSIONS
