Monogram ZIS420 Series, Руководство по установке

Страница: 40 / 116

40
Installation Instruction - Stainless Steel Installation
STEP 11 CONNECT POWER, CLOSE
GRILLE PANEL
• Open the grille panel.
• Plug in the power cord (if necessary) by reaching
into the opening next to the water filter. The water
filter guard will need to be removed for access (some
models). Remove the 3 screws holding it in place. If
access is still too tight, remove the 2 screws holding
the water filter bracket and move aside. Plug in the
power cord. Secure the bracket and guard with the
original screws.
• Check to make sure
power to refrigerator
is on by opening
refrigerator door to
see if interior lights
are on.
• The temperature
controls are preset
at 37°F (3°C) for
the fresh food
section and 0°F (-18°C) for the freezer.
• Allow 24 hours to stabilize before making adjustments.
Water Filter
Guard in Front of
Electric Outlet
Access
Bracket
Screws
Screws
STEP 12 START ICEMAKER
• The icemaker will be ON when unit is plugged in.
• The icemaker will begin operation automatically.
• Be sure nothing interferes with the sweep of the feeler
arm.
• Discard the first full bucket of ice cubes.
• To turn the icemaker off, depress the – and +
refrigerator in the Fresh Food controls for 5 seconds.
The display will show ICE OFF.
• To turn the icemaker back on, depress the – and +
refrigerator in the Fresh Food controls for 5 seconds.
STEP 10 CONNECT WATER SUPPLY
(Cont.)
SmartConnect ™ Tubing:
NOTE: The only Monogram-approved plastic tubing is
supplied in the SmartConnect ™ Refrigerator Tubing kits.
Do not use any other plastic water supply line because
the line is under pressure at all times. Other types of
plastic may crack or rupture with age and cause water
damage to your home.
SmartConnect ™ Refrigerator Tubing Kits are available
in the following lengths:
2’ (.6 m) WX08X10002
8’ (2.4 m) WX08X10006
15’ (4.6 m) WX08X10015
25’ (7.6 m) WX08X10025
• Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression nut
until it is just hand tight.
• Tighten one additional turn with a wrench.
Overtightening can cause leaks!
• Turn on the water to check for leaks.
• Run dispenser, if available, for 2 minutes or 1 gallon of
water. It is normal for the dispenser to sputter for the
first few cups
NOTE: Make sure excess tubing length does not
interfere with the toekick installation.
CAUTION
To minimize the risk of personal injury,
avoid contact with the moving parts of the ejector
mechanism, or with the heating element that releases the
cubes. Do not place fingers or hands on the automatic ice
making mechanism while the appliance is plugged in.
ATTENTION
Afin de réduire le risque de blessure,
évitez tout contact avec les pièces mobiles du mécanisme
d’éjection ou l’élément chauffant qui libère les cubes. Ne
placez pas les doigts ou les mains sur le mécanisme de
production de glace automatique lorsque l’électroménager
est branché dans la prise électrique.
PRECAUCIÓN
Para minimizar el riesgo de
lesiones personales, evite el contacto con las partes móviles
del mecanismo eyector o con el elemento de calefacción
que libera los cubos. No coloque los dedos ni las manos en
el mecanismo de la máquina de hielo automática mientras el
electrodoméstico se encuentre enchufado.
31-1000450 Rev. 1