manualshive.com logo in svg

Monico CDL, Инструкция по установке и эксплуатации

Поделиться
Скачать
Monico CDL Скачать руководство пользователя страница 13

- 13 - 

 

 

 

Host Connections 

The Host device (PLC, HMI, Building Management System, etc.) is connected to the Monico Gateway 
through the Ethernet Port (RJ-45 Jack-Shielded).  By default the Monico Gateway supports Modbus TCP 
Slave, BACnet UDPIP Slave, & SNMP over Ethernet.  The Monico Gateway is fully capable of providing data 
via hundreds of other protocols and/or serially as an option. The above mentioned protocols can be 
established at either 10 BASE-T or 100 BASE-TX. The Gateway’s RJ45 jack is wired as a NIC (Network  
 
 
Interface Card). For example, when wiring to a hub or switch use a straight-through cable, but when 
connecting to another NIC use a crossover cable.  

Default IP Address is 192.168.1.10

 

 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
As stated, the default Monico Gateway protocols include Modbus Slave, BACTnet UDPIP Slave, and SNMP 
over Ethernet.  The data maps for each configuration can be downloaded from 

http://www.monicoinc.com/support

 . 

 

 

 

Содержание CDL




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды