This toilet suite must be installed by a
licensed plumber in accordance with local,
State and National Standards and
Regulations.
Before Installation
The Concerto Heated Bidet Suite requires the
following setout for bottom entry installation as well as external
connection requirements for water and power supply for the
Heated Bidet Seat.
Setout
90-180mm setout for S trap and 180mm for P trap.
This toilet is supplied with a vario bend S trap. Please note, a
suitable P trap connection can be installed when required. Floor
and wall must be perpendicular and the toilet must be installed
on a level surface.
Smart Seat Plumbing
The Concerto Heated Bidet Seat
requires water supply on the left of the toilet so that a T valve
and hose may be installed as part of the smart seat installation
(see figure on right).
Smart Seat Power Supply
The Concerto Heated Bidet
Seat requires a power outlet to the right of the toilet that must be
installed as per local, State and National regulations.
Please note:
Product measurements are subject to
some variance due to manufacturing process.
Always check physical product dimensions
prior to setout and installation.
Installation Guide
1. Install the floor fixing kit, excluding the external screws:
a) Place pan into position, tracing around the outside
of the pan and marking floor alongside the two holes
on either side of the pan.
b) Remove pan and mark points for bracket installation
on inside of pan floor area and in line with pan holes
from 1(a), allowing clearance for pan thickness (see
Fig.2).
c) Drill holes into floor to required depth and apply wet
area silicone into the holes and to base of floor
bracket. Install the floor bracket using floor plugs,
washers and screws supplied (Fig.3). Do not install
external screws until Step 10.
2. Into the 2 holes in the top rear of the pan, install the pan
spigots, washers and nuts (Fig.4) with the cistern to be
attached in Step 7. Feed a flexible hose (not supplied)
through bottom entry hole of pan and then continue to
feed the hose out through the top of the pan.
3. For S trap installation, position the vario bend S Trap and
determine whether trimming is required to meet pan outlet
and waste connections (Fig 5). If trimming is required,
measure the vario bend carefully, mark and then cut
accordingly. Anchor vario bend to wall by measuring,
marking, drilling and fixing (Fig.6).
4. Replace vario bend cover and install, ensuring that the
connection points are secured correctly with a complete
seal.
5. Install the Cistern Outlet Seal to base of cistern, over the
outlet flush pipe (Fig.7).
6. Attach the flexible hose (from step 2) to the inlet valve
connection on bottom of cistern. Please note the inlet
valve position can be changed between right side and
left side with the unused inlet valve to be sealed with the
Inlet Plug supplied.
7. Using the Pan/Cistern Bolts provided, connect the cistern
and pan together (Fig.8). If necessary, the outlet flush
valve may be temporarily removed to make it more
accessible to fix the pan and cistern bolts into place.
Ensure the outlet flush valve is placed back into position.
8. Install flush button to cistern cover, adjusting toggles if
needed (Fig.9).
9. Before fixing external screws into side of toilet, connect
water supply and conduct several flush tests and ensure
that there are no leaks.
10. Install external screws to fixing brackets within pan
(Fig.10) and cover with white caps provided (Fig.11).
11. Complete installation of pan and cistern by sealing
around base of toilet with a bead of wet area silicone
and allow to dry before use (Fig.12).
12. For installation of Concerto Heated Bidet Seat, follow
installation instructions (supplied separately).
Fig.1
Fig.3
Fig.2
Fig.4
Fig.5
Fig.6
Fig.7
Fig.8
Fig.9
Fig.10
Fig.11
Fig.12
Pan Fixing Bolts
2
www.mondella.com.au
Support & Technical Advice
Email: [email protected]
