background image

Hand Crimp Tool .090” (23mm) Slip-on Receptacle Terminal 

Doc No: ATS-6382595HM 

Release Date: 06-25-12 

UNCONTROLLED COPY

 

Page 4 of 6 

Revision: A 

Revision Date: 06-25-12 

 

Miscrimps or Jams 

 
Should this tool ever become stuck or jammed in a partially closed position, 

Do Not

 force the handles

 

open or 

closed

.  The tool will open easily by lifting the ratchet release lever.  See Figure 6. 

 

Warranty 

 
This tool is for electrical terminal crimping purposes only.  This tool is made of the best quality materials.  All vital 
components are long life tested.  All tools are warranted to be free of manufacturing defects for a period of 30 
days.  Should such a defect occur, we will repair or exchange the tool free of charge.  This repair or exchange will 
not be applicable to altered, misused, or damaged tools.  This tool is designed for hand use only.  Any clamping, 
fixturing, or use of handle extensions voids this warranty. 

 

CAUTION:

 Repetitive use of this tool should be avoided. 

 

CAUTIONS: 

 
1.

 

Manually powered hand tools are intended for low volume or field repair.  This tool is 

NOT

 intended for 

production use.  Repetitive use of this tool should be avoided. 

2.

 

Insulated rubber handles are not protection against electrical shock. 

3.

 

Wear eye protection at all times. 

4.

 

Use only the Molex terminals specified for crimping with this tool. 

 

CAUTION

:  Molex crimp specifications are valid only when used with Molex terminals and tooling. 

 

Applications for the Modular Crimp Head 

 

WARNING

NEVER

 

operate, service, install, or adjust this Modular Crimp Head without proper instruction 

and without first reading and understanding the instructions in the proper Manual or Specification Sheet.  
See Chart below for the correct Manual or Specification Sheet. 

 

WARNING

NEVER

 

install tooling or service this tool while it is into any power source.  Disconnect the 

power by unplugging or turn off the Actuator from its power source. 

 

CAUTION: 

Keep fingers away from the crimping area when operating this tool.  It may cause severe injury. 

 

CAUTION: 

Wear safety glasses when operating or serving this tool. 

Содержание 63825-9570







Отзывы: