manualshive.com logo in svg

Mohawk FL-25, Руководство пользователя, Страница: 14 / 58

Поделиться
Скачать
Mohawk FL-25 Скачать руководство пользователя страница 14

MOHAWK MODEL TR-25A, FL-25, TR-19 

14 

 

INSTALLATION INSTRUCTIONS 

 

SET THE MAIN SIDE OF THE FORE CROSSRAIL INTO PLACE AT THE 
BASE OF THE MAIN SIDE POSTS. BLOCK UP USING THE 4 X 4 X 12” 
DUNNAGE. 
ROUTE  THE  FORE  CROSSRAIL  CHAIN  THROUGH  THE  FORE 
CROSSRAIL.  
  
SET THE MAIN SIDE TRACK INTO PLACE. BLOCK UP USING THE 8 X 
8 X 24” DUNNAGE.  
 
SET THE OFF SIDE TRACK INTO PLACE. BLOCK UP USING THE 8 X 8 
X 24” DUNNAGE NOTE THAT THE RACE FOR THE RJ-25 IS TO BE TO 
THE INSIDE OF THE TRACKS.  
 
SET  THE  MAIN  SIDE  OF  THE  AFT  CROSSRAIL  INTO  PLACE  AT  THE 
BASE OF THE MAIN SIDE POSTS. BLOCK UP USING THE 4 X 4 X 12” 
DUNNAGE. 
 
ROUTE  THE  AFT  CROSSRAIL  CHAIN  THROUGH  THE  AFT 
CROSSRAIL.  
 
ASSEMBLE THE FOUR LIFTING CHAINS (TWO SHORT & TWO LONG) 
FROM THE HYDRAULIC CYLINDER TO THE CHAIN BLOCKS ON THE 
CROSSRAILS. 
 
SET THE TWO OFF SIDE POST INTO PLACE ON THE FLOOR LAYOUT. 
ASSEMBLE THE CHAIN CONNECTORS AT THE THROUGH HOLES AT 
THE  TOP  OF  THE  OFF  SIDE  POSTS.  TIGHTEN  THE  CHAIN 
CONNECTORS  SO  THAT  THE  CONNECTOR  IS  PAST  /  INTO  THE 
NYLON. 

NOTE

 

x

 

DO NOT DRILL THE ANCHOR HOLES FOR THE OFF SIDE POST. 
THIS  WILL  BE  PERFORMED  AS  A  FINAL  PART  OF  THE 
INSTALLATION. 

 
ASSEMBLE  THE  TWO  TRACK  STOPS  TO  THE  FORE  END  OF  THE 
TRACKS  USING  THE  EIGHT  3/4  X  2-1/2”  BOLTS,  AND  NYLON  LOCK 
NUTS. 
 
ASSEMBLE  THE  RAMPS  TO  THE  AFT  END  OF  THE  TRACKS  USING 
THE EIGHT 3/4 X 2-1/2” BOLTS, AND NYLON LOCK NUTS. 
 
INSTALL THE PNEUMATIC LOCK RELEASE COMPONENTS PER THE 
INSTRUCTIONS AND DIAGRAMS ON DWG. 025-012-128. 
 
INSTALL A CLEAN DRY SHOP AIR SUPPLY TO THE REGULATOR. 
SET REGULATOR TO 80 P.S.I. 
 
CYCLE  THE LOCK RELEASE AND ENSURE THAT ALL FOUR LOCKS 
ARE RELEASING PROPERPLY.  
 
CHECK  FOR  ANY  AIR  LEAKS,  CORRECT  AS  REQUIRED  BEFORE 
PROCEDING TO THE NEXT STEP. 
 
TURN THE ELECTRIC CIRCUIT BREAKER FOR THE UNIT ON. 
 
NOTE  THE POSITION OF THE MAIN SIDE TRACK. ALIGN THE TABS 
ON  THE  CROSSRAILS  TO  THE  MAIN  SIDE  TRACKS.  ALSO  SET  THE 
OFF SIDE TRACK AT EIGHT FEET FROM THE OUTSIDE OF THE MAIN 
SIDE TRACK. 

ENGAGE  THE  UP  BUTTON  RAISING  THE  UNIT  APPROXIMATELY 
THREE FEET.  
 
CYCLE  THE  UNIT  2  TIMES  NOTING  THE  POSITION  OF  THE 
CROSSRAILS INSIDE THE POSTS.  
 
LOWER  THE  UNIT  ONTO  THE  MECHANICAL  LOCKS.  VERIFY  A 
POSITIVE  LOCK  SEAT  ON  THE  MAIN  AND  OFF  SIDE  POSTS. 
(MECHANICAL LOCK TO LATCH RACK IN POST) ADJUST THE  OFF 
SIDE POST AS NEEDED TO ACHIEVE A GOOD SEAT.  
 

NOTE  

x

 

ENSURE LEVEL POSTS AND A GOOD LOCK SEAT ON THE MAIN 
AND  OFF  SIDE  POST  BEFORE  DRILLING  THE  MOUNTING 
HOLES. 

 

DRILL  THE  MOUNTING  HOLES  IN  THE  CONCRETE  USING  THE 
HOLES  IN  THE  BASE  PLATE  AS  A  DRILL  GUIDE..  SECURE  THE  OFF 
SIDE POSTS TO THE SHOP FLOOR USING THE EIGHT 3/4 X 5” WEJ-IT 
ANCHORS. 
 

LEVELING THE TRACKS 

 

LEVEL  THE  TRACKS  FRONT  TO  REAR  BY  ADJUSTING  THE  CHAIN 
CONNECTORS AT THE END OF THE HYDRAULIC CYLINDER. 
 
LEVEL  THE  TRACKS  SIDE  TO  SIDE  BY  ADJUSTING  THE  CHAIN 
CONNECTORS AT THE TOP OF THE OFF SIDE POSTS. 

 

NOTE 

x

 

ALL  BOLTS  USING  NYLON  LOCK  NUTS.  ALL  BOLTS  MUST 
EXTEND  PAST  THE  NYLON  BY  THREE  THREADS.  THIS 
INCLUDES THE ADJUSTABLE CHAIN CONNECTORS.

 

 

SECURE  THE  TWO  HYDRAULIC  HOSES  TO  THE  TOP  RAIL  USING 
THE THREE HOSE CLAMPS AND 5/16 SELF TAPING SCREWS. 
 
REFERENCE DIAGRAM IN BACK OF MANUAL. APPLY ALL DECAL IN 
APPROPRIATE LOCATIONS. 
 

NOTE 

 

x

 

APPLY DECALS TO A CLEAN, OIL & DIRT FREE SURFACE.  

 
 
 
 
 

 

 
 
 
 

Содержание FL-25



























































Отзывы:

Нет отзывов