background image

02/02 AWB8230-1447GB

Restoring the Default Settings

3

Restoring the Default Settings

Initialization

Two different types of initialization are available:

• Clearing the fault history register
• Restoring the default parameter settings 

To delete the fault history register or to restore the default 
settings, proceed as follows:

X

Make sure that PNU b85 holds the value.

X

Under PNU b84 (initialization), enter 00 or 01.

X

Press the ENTER key to save the value.

X

On the keypad, press both arrow keys and the PRG key at the 
same time and keep them pressed.

X

While holding the arrow and PRG keys, briefly press the 
OFF key.

X

Keep the other three keys pressed for three further seconds until 
the following flashing display appears: 

d 00

X

Now release all keys again.

Initialization is now complete. 

Country version

Here, you define the country-specific parameter set which will be 
loaded during initialization (

a

 PNU b84). 

PNU

Name

Adjustable in 
RUN mode

Value

Function

WE

b84

Initialization

00

Clearing the fault history register

00

01

Restoring the default parameter settings

PNU

Name

Adjustable in 
RUN mode

Value

Function

WE

b85

Country 
version

00

Japan

01

01

Europe

02

USA

03

Reserved

Содержание DF5 series












Отзывы: