background image

Facility Name:

City:

State:

Modular Services Company

E-mail to: 

Call with your questions:

Attention Customer Service

or

[email protected]

or

Customer Service

109 N.E. 38th Street

1-800-687-0938 x7245

Oklahoma City, OK  73105

Record Unit Serial Number

 (On Top Plate)

Verif

y Room/Side correct 

per unit 

Mounting Structure

installed

per

Components unpacked and  verified

per Fi

gs

Main Bearing Assy level, 

and nuts 

tor

qued

per

Hoses and 

cables routed  and Service 

Column

mounted

pe

r

Ground straps  connected

per

Medical gas  connections and testin

g

Electrical

connections and testing  per state and 

Brake stops  set at proper  locations

per

A

ll covers, end  caps, and 

shrouds

installed and 

Unit power,  gases, low 

voltage

devices, and 

range of  motion are 

Stratus™ Warranty Checklist

Please verify correct room/side location for each unit and initial all of the items below that apply.   Any steps that are not 

correctly completed could void your product 

warranty.  The  Stratus Warranty Checklist must be submitted to Modular Services Company within 30 days of installation for you

r factory warranty to be activated.

The com

pleted forms ma

y be mailed to:

Verifications

Verify

Room/Side

correct

per

unit

label

installed

per

Figs 1 & 2

verified

per

Figs

4 & 5

torqued

per

Fig 8

mounted

per

Figs 9 & 10

connected

per

Fig 11

and

testing

per NFPA 99

per

state

and

local codes

locations

per

Fig 13

installed

and

proper fit

motion

are

fully functional

Verified By (Please print):

Signature:

Date:

Title:

Company:

Received By:

Job #

Date:

All Rooms/sides verified?

DCN# 10-1079 — Rev. 3/2011

Date Filed in CNG:

Modular Services Use Only

Содержание STRATUS II















Отзывы: