Modine Manufacturing Atherion MPR Скачать руководство пользователя страница 1

Страница: 1 / 16

ATH15-501.0 (

Supplement to ATH15-500.10

)

August, 2021

INSTALLATION AND SERVICE MANUAL SUPPLEMENT

GAS HEAT OPTION WITH FURNACE MODEL DIGIT 11=6, 9, A, B, C, OR D

Packaged Ventilation/Dedicated Outside Air System (DOAS)

model MPR

ATH15-501.0

5H0899700001

THIS MANUAL IS THE PROPERTY OF THE OWNER.

PLEASE BE SURE TO LEAVE IT WITH THE OWNER WHEN YOU LEAVE THE JOB.

Improper installation, adjustment, alteration,

service or maintenance can cause property

damage, injury or death, and could cause

exposure to substances which have been

determined by various state agencies to cause

cancer, birth defects or other reproductive

harm. Read the installation, operating and

maintenance instructions thoroughly before

installing or servicing this equipment.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury, death or property

damage.
Be sure to read and understand the installation,

operation and service instructions in this manual.
Improper installation, adjustment, alteration,

service or maintenance can cause serious

injury, death or property damage.
Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch, do not

use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from

a phone remote from the building.

Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call

the fire department.

Installation and service must be performed by a

qualified installer, service agency or the gas

supplier.

WARNING

These instructions apply only to the gas control options identified on page 3.
• If the model MPR unit DOES NOT include the controls identified, these

instructions are not applicable and not to be used.

• If the model MPR unit DOES include a gas heat option with control

identified as applicable on page 3, these instructions must be used in

conjunction with the Installation & Service Manual, Literature

#ATH15-500.10 that shipped with the unit. Read those instructions

thoroughly before installing or servicing this equipment.

STOP

Содержание Atherion MPR

















Результаты поиска

Содержание Atherion MPR

Отзывы:

Похожие инструкции для Atherion MPR

Бренды по названию

Популярные бренды

Modine Manufacturing Atherion MPR, Дополнение к руководству по установке и обслуживанию

Результаты поиска

Содержание Atherion MPR

Отзывы:

Похожие инструкции для Atherion MPR

Бренды по названию

Популярные бренды