background image

18 

 

When using the Mobeye Internet Portal 
1111 IN2RESET:SEND 

Restore message via portal for input 2 

After a first restore message the text is visible (and can be changed) under 
the message texts in the Mobeye Internet Portal. 

 

When using your own SIM card (replace yourowntext for another text) 
1111 IN2RESET:SEND,yourowntext  Restore SMS for input 2 

 

For more information, see the support page on www.mobeye.com. 

5.8

 

POWER FAILURE MESSAGE 

If the Mobeye WaterGuard-FS is supplied with external power and the power 
fails, it can send alarm messages. If the setting is "OFF", no message is sent.  

When set to “ALARM”, noti

fications are sent to the set contacts. When using 

your own 

SIM card, the setting “ALERT” only results in an SMS 

notification to 

TEL1. The default setting is "ALERT". 

5.9

 

POWER FAILURE DELAY TIME 

To avoid false alarms caused by short power failures, a power failure delay 
time can be set. This defines the time between the initial power failure and 
the  alarm  notification.  If  the  power  is  restored  within  the  delay  time,  no 
alarm is sent. The time can be set between 0 and 24 hours. As default, the 
delay time is set to 4 hours. 

5.10

 

AUTOMATIC ARMING / DISARMING 

The Mobeye WaterGuard-FS only works if the unit is armed, which is done 
via the on/off button. It is possible to automatically arm and disarm the unit, 
based  on  an  arming  and/or  disarming  time  scheme.  Two  schemes  can  be 
entered,  which  can  be  assigned  to  the  days  in  the  week  (e.g.  to  have  a 
different weekend scheme). 
As default the automatic (dis) arming times are valid for all days. It is possible 
to assign them to only a few days in the week. In this way it is possible to 
have two different schemes, which are valid on different days. 
As value the weekdays can be entered. Monday is 1, Tuesday is 2, etc. If the 
scheme  is  valid  for  several  days,  the  days  can  be  set  in  a  row  (e.g.  12345 
means Monday till Friday). 

Содержание CM4300FS

































Отзывы: