background image

21 

6.  PROGRAMMING WHEN USING OWN SIM CARD 

If your own SIM card is used, programming proceeds via SMS commands. The GSM 
module  requires  network  connection  during  programming.  If  the  Mobeye  Panic 
Button runs entirely on batteries, it must first be put into programming mode. 

6.1  PROGRAM MODE 

To program the unit with SMS commands, the GSM module needs to be open and 
connected to the network.  
In the situation that the Panic Button is connected to an external power supply, it has 
continuous network connection and the unit is permanently in program mode. 
A  battery-operated  Mobeye  Panic  Button  switches  to  the  program  mode  after 
pressing  the  on/off  button  for  5  seconds  until  the  LED  starts  flashing.  Alternatively 
the batteries are re-inserted. 
 
While searching for the GSM network connection the outside LED flashes green and 
red, followed by blinking fast shortly. This process normally takes 10-30 seconds. As 
soon as the network has been established and the program mode has been reached 
the  LED  flashes  1 sec. on/1 sec. off (or  stays on continuously in case the  unit  has 
been configured yet). 
During  3  minutes  the  GSM  module  remains  active,  ready  to  receive  SMS 
commands.  In  a  battery-operated  unit  a  time-out  occurs  if  no  correct  command  is 
received for 3 minutes, the GSM module switches off in order to save the batteries. 
In this low power mode the LED flashes once per 3 seconds. 

6.2  PROGRAM AT LEAST ONE TELEPHONE NUMBER  

The  Mobeye  Panic  Button  is  able  to  send  messages  up  to  5  telephone  numbers. 
The  first  telephone  number  (TEL1)  belongs  to  the  administrator.  Technical 
messages  (such  as 

battery  low

)  are  sent  to  the  administrator  only.  Without  the 

administrator

’s phone number, the Mobeye Panic Button cannot function.  

When the Panic Button is in initial (factory) status and the batteries are inserted (so 
the  LED  is  flashing),  the  administrator

’s  number  is  programmed  by  calling  the 

telephone number of the Mobeye Panic Button using the administrator

’s phone. The 

Содержание CM2500

































Отзывы: