INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product
s
:
WGULED / WGULEN / WHGULED / WSGULED
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•
This product is safe for use as a drive-over fitting (1000kg @ 5mph)
•
This product is Class I and must be earthed
•
This product is IP67 rated
INSTALLATION
•
Provide power to the required point of installation (refer to BS7671 for correct cabling methods).
Suitable IP rated junction boxes should be used where required
•
Cut a suitable hole in the mounting surface as per the cut-out details (see Fig.1) ensuring not to
infringe with any joists, gas / water pipes or electrical cables. The sleeve should be used for direct
mounting in the ground
Product Code
Cut-out diameter (mm)
WGULEN
92
WGULED
92
WHGULED
92
WSGULED
92
Fig. 1
•
We recommend not installing in areas where there is a high risk of flooding or areas where water may
sit on top of the fitting (see Fig. 2)
•
Ensure a minimum of 300mm of drainage is put below the luminaire (see Fig. 2)
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product
s
:
WGULED / WGULEN / WHGULED / WSGULED
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•
This product is safe for use as a drive-over fitting (1000kg @ 5mph)
•
This product is Class I and must be earthed
•
This product is IP67 rated
INSTALLATION
•
Provide power to the required point of installation (refer to BS7671 for correct cabling methods).
Suitable IP rated junction boxes should be used where required
•
Cut a suitable hole in the mounting surface as per the cut-out details (see Fig.1) ensuring not to
infringe with any joists, gas / water pipes or electrical cables. The sleeve should be used for direct
mounting in the ground
Product Code
Cut-out diameter (mm)
WGULEN
92
WGULED
92
WHGULED
92
WSGULED
92
Fig. 1
•
We recommend not installing in areas where there is a high risk of flooding or areas where water may
sit on top of the fitting (see Fig. 2)
•
Ensure a minimum of 300mm of drainage is put below the luminaire (see Fig. 2)
Fig. 1
• We recommend not installing in areas where there is a high risk of flooding or areas where water may sit on
top of the fitting (see Fig. 2)
• Ensure a minimum of 300mm of drainage is put below the luminaire (see Fig. 2)
Fig. 2
•
There must be enough cable below the luminaire to carry out maintenance work (see Fig. 3)
Fig. 3
•
With the Allen key provided, remove the hex screws fixing the bezel to the luminaire
•
Remove the bezel, gasket and glass (see Fig. 4)
Fig. 4
•
Remove the screws around the top of the fitting and pull away from the plastic sleeve
•
Feed appropriate cable through the compression glands at the base of the fitting
•
Secure the sleeve (if required) into the mounting surface
•
Connect the luminaire to the mains supply ensuring the correct polarity is observed L - Live (brown), E
- Earth (green/yellow), N - Neutral (blue)
Fig. 2
