background image

INSTALLATION & MAINTENANCE MANUAL 

These instructions should be read carefully and retained after installation by the end user for future reference 

and maintenance. 

These instructions should be used to aid installation of the following product

(s)

AMLEDB / AMLEDR / AMLEDW 
SAFETY 

 

This product must be installed in accordance with the latest edition of the IEE Wiring Regulations 

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician 

 

Please isolate mains prior to installation or maintenance 

 

Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of 

the circuit cable, fuse or circuit breaker 

 

Please note the IP (Ingress Protection) rating of this product when deciding the location for installation 

 

This product is Class II double insulated  

 

This product is IP54 rated 

INSTALLATION 

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the 

manufacturer of the sensors that they are compatible with LED lamps/luminaires. 

 

Provide power to the required point of installation (refer to BS7671 for correct cabling methods). 

Suitable IP rated junction boxes should be used where required 

 

Remove the diffuser and gear tray from the body 

 

Drill the fixing holes in the rear of the fitting. Mark the location of the fixing holes and drill ensuring not 

to infringe with any gas/water pipes or electrical cables  

 

Drill out one of the 20mm drilling guides on the fitting, and fit a suitable external grommet or 

compression gland (not included) 

 

Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (Brown), 

N - Neutral (Blue) (see Fig. 1) 

 

 

 

 

 

Fig. 1 

 

 

 

 

 

Replace the gear tray and diffuser ensuring the seal is in place 

 

Switch on and check for correct operation 

WARNING 

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance 

testing. Irreparable damage will occur if this instruction is not followed. 

GENERAL 

This product contains a light source of energy efficiency class E to Regulation (EU) No. 2019/2015. 

 

This product contains an LED light source which can be replaced by the end user and a control gear which can 

be replaced by a professional. 

 

 

• Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (Brown),
N - Neutral (Blue) (see Fig. 1)

INSTALLATION & MAINTENANCE MANUAL 

These instructions should be read carefully and retained after installation by the end user for future reference 

and maintenance. 

These instructions should be used to aid installation of the following product

(s)

AMLEDB / AMLEDR / AMLEDW 
SAFETY 

 

This product must be installed in accordance with the latest edition of the IEE Wiring Regulations 

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician 

 

Please isolate mains prior to installation or maintenance 

 

Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of 

the circuit cable, fuse or circuit breaker 

 

Please note the IP (Ingress Protection) rating of this product when deciding the location for installation 

 

This product is Class II double insulated  

 

This product is IP54 rated 

INSTALLATION 

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the 

manufacturer of the sensors that they are compatible with LED lamps/luminaires. 

 

Provide power to the required point of installation (refer to BS7671 for correct cabling methods). 

Suitable IP rated junction boxes should be used where required 

 

Remove the diffuser and gear tray from the body 

 

Drill the fixing holes in the rear of the fitting. Mark the location of the fixing holes and drill ensuring not 

to infringe with any gas/water pipes or electrical cables  

 

Drill out one of the 20mm drilling guides on the fitting, and fit a suitable external grommet or 

compression gland (not included) 

 

Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (Brown), 

N - Neutral (Blue) (see Fig. 1) 

 

 

 

 

 

Fig. 1 

 

 

 

 

 

Replace the gear tray and diffuser ensuring the seal is in place 

 

Switch on and check for correct operation 

WARNING 

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance 

testing. Irreparable damage will occur if this instruction is not followed. 

GENERAL 

This product contains a light source of energy efficiency class E to Regulation (EU) No. 2019/2015. 

 

This product contains an LED light source which can be replaced by the end user and a control gear which can 

be replaced by a professional. 

 

 

Fig. 1

• Replace the gear tray and diffuser ensuring the seal is in place
• Switch on and check for correct operation

WARNING

GENERAL

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance 
testing. Irreparable damage will occur if this instruction is not followed.

This product contains a light source of energy efficiency class E to Regulation (EU) No. 2019/2015.

This product contains an LED light source which can be replaced by the end user and a control gear which can 
be replaced by a professional.

Содержание AMLEDB






Отзывы: