background image

Weld Control Selector Guide - Page 9

ESaB 

(includes L-tec & Linde)

The 005-0206 Kit will interface a Prince XL Spool-gun to a Migmaster 250. It plugs directly into the 

amphenol on the front of the unit and includes everything needed to interface to that power supply.

A Cobramatic system may be used on this unit and would be interfaced as 

follows:

1.  Plug the 115VAC plug from the Cobramatic Cabinet into a standard 

wall outlet.

2. Connect the 

black

 and 

white

 contactor leads from the Cobramatic 

Cabinet to the 8-Pin (Spool-gun) plug on the Migmaster 250:

 

the 

black

 wire to Pin

 a

 and the 

white

 wire to Pin 

B

. Put the 

Cobramatic in CLOSING CONTACTS Position (see Appendix for 

contactor information).

E-1

The 005-0624 Kit will interface a Prince XL Spool-gun to a Migmaster 251. It replaces a blank 

panel on the front of the machine and includes everything needed to interface to this welder. 

A Cobramatic system may be used on this unit and would interface as follows:

1.  Plug the 115VAC plug from the Cobramatic Cabinet into a standard wall outlet

2.  Install 1/4 (.250) wide female spade connectors to the 

Black

 and 

White

 contactor wires extending 

from the Cobramatic Cabinet to the male spade connectors located on the inside wall of the 

welder by the wire feeder. First remove the existing trigger leads from the Migmaster torch. Place 

the Cobramatic in the CLOSING CONTACTS position (see Appendix for contactor information).

3.  Place the power cable lug from the Cobramatic Cabinet on the positive ( + ) terminal of the 

Migmaster 251 located by the wire feeder inside the welder.

The older L-Tec 225 is connected as follows:

1.  Install 1/4 (.250) wide female spade connectors to the 

Black

 and 

White

 contactor wires extending 

from the WC-1 Weld Control or the Cobramatic Cabinet to the male spade connectors located on 

the inside wall of the welder by the wire feeder. First remove the existing trigger leads from the L-

Tec torch. Place the WC-1 or Cobramatic in the CLOSING CONTACTS position (see Appendix for 

contactor information).

2.  Plug the 115VAC plug extending from the WC-1 or Cobramatic into a standard wall outlet.

Note:  The feeder inside this unit will also be activated so disengage the spring tension on 

the drive roll.

The WC-1 Weld Control of the Cobramatic Cabinet may be connected to the Migmaster 300 as follows:

1.  Plug the 115VAC plug from the WC-1 Weld Control of the Cobra 

Cabinet into a standard wall outlet. 

2. Connect the 

Black

 and 

White

 contactor leads from the WC-1 or 

Cobramatic to the 8-Pin plug on the Migmaster 300. The 

black

 

wire to 

Pin a

 and the 

white

 wire to 

Pin B.

 Put the WC-1 or 

Cobramatic into CLOSING CONTACTS position (see Appendix for 

contactor information).

3. A male Dinse style connector is required on this machine. Cut the 

lug off of the power cable on the Prince XL Spool-gun and replace 

with the Dinse connector. 

note - 

The power cable to the Cobramatic hooks to bolt holding an 

existing cable just in front of the MM-250's wire feed motor. Place the 

Switch (Std/Spool-gun) in Spool-gun position.

E-2

E-3

E-4

8-Pin amphenol

Socket

153-0922

Cord Clamp

411-0191

Rubber Boot

301-0054

8-Pin amphenol

Socket

153-0922

Cord Clamp

411-0191

Rubber Boot

301-0054

DInse Connector

Male Plug

153-0755

Содержание ELECTRIC ARC WELDING EQUIPMENT














































Отзывы: