background image

6

Consult the owner’s manual for recommended accessories.  Using improper accessories 

may increase the risk of personal or by-stander injury. 

Serious injury could occur if a power tool is tipped, or if a cutting tool is unintentionally 

contacted.

Before using a power tool, check for damaged part. A guard or any other part that is 

damaged should be carefully checked to determine if would operate properly and perform 

its intended function.  Always check moving parts for proper alignment or binding. Check 

for broken parts and mountings and all other conditions that may affect the operation of 

the power tool. A guard, or any damaged part, should be properly repaired or replaced.

ALWAYS

 feed work into a blade or cutter against the direction of rotation. A blade 

or cutter should always be installed such that rotation is in the direction of the arrow 

imprinted on the side of the blade or cutter.

TURN POWER OFF - Do not leave a tool until it comes to a complete stop.  Always 

turn a power tool OFF when leaving the work area, or, when a cut is finished.

CALIFORNIA PROPOSITION 65 MESSAGE

USE RECOMMENDED ACCESSORIES

NEVER LEAVE A TOOL UNATTENDED

NEVER STAND ON THE TOOL

CHECK FOR DAMAGED PARTS

DIRECTION OF FEED

WARNING

Some dust created by power sanding, polishing, grinding, drilling, and other construction activities 

contain chemicals known (to the State of California) to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are: 

 Lead, from lead-based paints 

 Crystalline silica, from bricks and cement and other masonry products 

 Arsenic and chromium, from chemically treated lumber 

For further information, consult the following sources: 

http://www.osha.gov/SLTC/silicacrystalline/index.html 

http://www.cdc.gov/niosh/consilic.html 

http://oehha.ca.gov/prop65/law/P65law72003.html 

http://www.dir.ca.gov/Title8/sub4.html 

Your risk from these exposures varies depending on how often you do this type of work. To reduce 

your exposure to these chemicals, work in a well-ventilated area, and work with approved safety 

equipment, such as those dust masks that are specially designed to filter out microscopic particles.

MK-1503SS   

 

 

 

 

                                                                SAFETY

Содержание MK-1503SS

























Отзывы: