MK Diamond Products MK-145 Скачать руководство пользователя страница 9

 

MK Diamond Products Inc. Customer Service Department (800) 421-5830 

MK-145 

Revision 09/04, Effective date – September 23, 2004 

      Page 

9

 

SAFETY: 

 

 
 
 

 
Use only extensions cords that are intended for outdoor use.  These extension 
cords are identified by a marking "Acceptable for use with outdoor appliances; 
store indoors while not in use."  Use only extension cords having an electrical 
rating not less than the rating of the product.  Do not use damaged extension 
cords.  Examine extension cords before using and replace if damaged.  Do not 
abuse extension cords and do not yank on any cord to disconnect.  Keep cords 
away from heat and sharp edges.  Always disconnect extension cords from the 
receptacle before disconnecting the product form the extension cord. 
 

 

 
 
 

 
Use of undersize extension cords results in low voltage to the motor that can 
result in motor burnout and premature failure.  MK Diamond warns that 
equipment returned to us showing signs of being run in a low voltage condition, 
with undersized extension cord, will be repaired or replaced totally at the 
customers expense.  There will be no warranty claim. 
 
To choose the proper extension cord, 

• 

Locate the length of extension cord needed in TABLE 1 below. 

• 

Once the proper length is found, move down the column to obtain the correct 
AWG size required for that length of extension cord. 

 
 

 

Extension Cord Minimum Gage for Length 

 

 

Volts 

Total Length of Cord in Feet 

230V  

25 ft. 

50 ft. 

100 ft 

150 ft. 

 

AWG AWG AWG AWG 

 

18 16 16 14 

TABLE 1 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание MK-145

































Отзывы: