manualshive.com logo in svg

MK Diamond Products MK-145, Руководство пользователя и инструкции по эксплуатации

Поделиться
Скачать
MK Diamond Products MK-145 Скачать руководство пользователя страница 24

 

MK Diamond Products Inc. Customer Service Department (800) 421-5830 

MK-145 

Revision 09/04, Effective date – September 23, 2004 

      Page 

24

 

MAINTENANCE and TROUBLESHOOTING:

 

Diamond Blade Change-out: 

STEP ACTION 

1. 

Unplug the MK-145 
a)  Unplug the MK-145 from the power source 
b)  Unplug the MK-145 from the GCFI 

 
 
 
 
 

2. 

Remove Retaining Nut and Outer Flange 
a)  Hold the Diamond Blade still 
b)  Rotate the Blade Wrench counter-clockwise to 

loosen 

c)  Remove the Retaining Nut and Outer Flange 

 
 
 
 
 

3. 

Remove the Diamond Blade 
a)  Remove the Blade out from between the Table 

Blade Slot from below 

 
 
 
 
 

4. 

Install Diamond Blade 
a)  Orient the Blade to the Gear Shaft with the 

Directional Arrow facing out 

b)  Install the Blade through the Table Blade Slot 

from below 

 
 
 
 
 

5. 

Verify Blade Seated 
a)  Verify the Blade is seated on the Gear Shaft 
b)  Verify Blade Directional Arrow matches the 

Directional Arrow on the Blade Guard 

 
 
 
 
 

NOTE:  Do not “cross-thread the Retaining Nut during installation. 

 

6. 

Install The Retaining Nut and Outer Flange 
a)  Install the Plastic Outer Flange onto the Gear 

Shaft 

b)  Install the Retaining Nut onto the Gear Shaft 

 
 
 
 
 

7. Tightening 

Diamond 

Blade 

a)  Hold the Diamond Blade still 
b)  Rotate the Blade Wrench clockwise  to tighten – 

DO NOT OVER TIGHTEN 

 
 
 
 
 

8. 

Reinstall the Water Basin Cover 
a)  Insert the three (3) Cover Retaining Tabs into 

the three (3) Cover Alignment Slots 

b)  Seat the Water Basin Cover on the MK-145 
 

 
 
 
 
 

 

Blade Slot

Diamond Blade 

Installed on
Gear Shaft

Directional 

Arrow 

GFCI

Rotate to

loosen 

Blade 

Wrench 

Blade Slot

Diamond Blade 

Alignment 

Slot 

Retaining Tab 

Retaining nut

Rotate to

tighten 

Blade 

Wrench 

Outer Flange

Содержание MK-145

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды