manualshive.com logo in svg

MK Diamond Products MK-145, Руководство пользователя и инструкции по эксплуатации

Поделиться
Скачать
MK Diamond Products MK-145 Скачать руководство пользователя страница 6

 

MK Diamond Products Inc. Customer Service Department (800) 421-5830 

MK-145 

Revision 09/04, Effective date – September 23, 2004 

      Page 

6

 

SAFETY: 

 
REDUCE THE RISK OF UNINTENTIONAL STARTING. 

 
 

Make sure the ON/OFF switch is in OFF position before plugging in a power tool. 
 
 

USE RECOMMENDED ACCESSORIES. 

 

Consult the owner's manual for recommended accessories.  Using improper 
accessories may increase the risk of personal or by-stander injury.  
 

NEVER STAND ON TOOL. 

 

Serious injury could occur if a power tool is tipped, or, if the cutting tool is 
unintentionally contacted. 
 

CHECK DAMAGED PARTS. 

 

Before using a power tool, check for damaged parts.  A guard or another part that 
is damaged should be carefully checked to determine it would operate properly 
and perform its intended function.  Always check moving parts for proper 
alignment or binding.  Check for broken parts, mountings and all other conditions 
that may affect the operation of the power tool.  A guard, or any damaged part, 
should be properly repaired or replaced. 
 

DIRECTION OF FEED. 

 

Always feed work into a blade or cutter against the direction of rotation.  A blade 
or cutter should always be installed such that rotation is in the direction of the 
arrow imprinted on the side of the blade or cutter. 
 

NEVER LEAVE TOOL RUNNING UNATTENDED – TURN POWER OFF. 

 

Do not leave a tool until it comes to a complete stop. Always turn a power tool 
OFF when leaving the work area or when finished cutting. 
 

 

Hazard Symbols: 

 

ELECTRICAL SHOCK! 

 
 

Never touch electrical wires or components while the motor is running.  Exposed, 
frayed or worn electrical motor wiring can be sources of electrical shock that 
could cause severe injury, burns or death. 
 

ACCIDENTAL STARTS! 

 
 

Before plugging the equipment into an electrical outlet, be sure the ON/OFF 
switch is in the "OFF" position to prevent accidental starting.  Unplug the power 
tool before performing any service operation. 
 

ROTATING OR MOVING PARTS! 

 
 

Keep hands, feet, hair, and clothing away from all moving parts to prevent injury.  
Never operate a power tool with covers, shrouds, or guards removed. 
 

 
 

on

on

Содержание MK-145

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды