Mizuho Allegro 6800 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 61

Mizuho Allegro 6800 Скачать руководство пользователя страница 10

MIZUHOSI 2009

NW0510 Rev. D

10

4.0 BASIC OPERATION

4.1 Control Operation

For use with line power:

Plug  the  power  cord  into  a  properly  grounded  receptacle.  Refer  to  the  label  at  the
pedestal  end  of  the  base  for  input  voltage  requirements  (see  figure  4).    Turn  on  the
power switch and observe the green light in the switch indicating that power is applied
to the table.  This rocker switch is a combination on/off power switch, circuit breaker and
pilot light.

WARNING:

Ensure  that  the  battery  has  been  properly  charged  as  outlined  in  section  7.0.
Turn on the power switch.  The battery status LED on the hand pendant should be
green, indicating a charged battery.  The expected working life of a fully charged
battery  is  approximately  5  hours  at  10%  duty  cycle.    While  in  storage,  it  is
desirable that the table be plugged in and the power switch turned on so that the
batteries  remain  charged.    If  this  is  not  possible,  the  batteries  must  be  charged
for at least three hours a week.  This can be accomplished when using the table
under line power.

This symbol            indicates the external stud that is at the same potential as the
equipment  chassis.  If  the  AC  power  cable  is  not  connected  to  an  outlet  with  a
protective  earth  ground,  this  external  stud  should  be  connected  to  a  protective
earth ground.

4.2 Floor Lock

To  operate  the  floor  locks  via  the  hand  pendant,  press  and  hold  the  FLOOR  LOCK
button  until  the  floor  lock  is  completely  deployed.    The  green  indicator  light  marked
LOCKED WHEN  LIT  on  the  control  panel  and  the  FLOOR  LOCK  ON  LED  located  on
the hand pendant will be illuminated when it is locked.  To stow the floor locks via the
hand  pendant,  press  and  hold  the  FLOOR  UNLOCK  button  until  the  floor  lock  is
completely  retracted.    The  amber  indicator  light  marked  STOWED  WHEN  LIT  on  the
control panel and the FLOOR LOCK, STOWED LED located on the hand pendant will
be illuminated when they are stowed.

The  floor  locks  can  also  be  operated  by  the  floor  lock  buttons  on  the  sheet  metal
housing  of  the  pedestal  as  follows.    Press  the  button  labeled  DOWN  TO  LOCK,  and
hold  it  until  the  floor  lock  is  completely  deployed.    The  green  indicator  light  marked
LOCKED WHEN LIT on the control panel (see figure 3) and the FLOOR LOCK ON LED
located  on  the  hand  pendant  (see  figure  6)  will  be  illuminated  when  it  is  locked.    To
release  the  floor  lock,  press  the  button  labeled  UP  TO  UNLOCK  and  hold  it  until  the
floor  lock  is  completely  retracted.    The  amber  indicator  light  marked  STOWED WHEN
LIT on the control panel and the FLOOR LOCK STOWED LED on the hand pendant will
be illuminated when it is stowed.

«
...
8
9
10
11
12
...
»

Содержание Allegro 6800






























































Отзывы:

Нет отзывов