background image

– 19 –

Has the unit been installed correctly?

   Pay attention to operating noises!

When you install the unit, take care to choose a place that can comfortably stand the weight of the unit and does not increase the operating noise
or vibration. If there is any likelihood that vibration may be transmitted through the house, fix the unit with the aid of vibration-proof pads
between the unit and the fittings.

Select a place where cold or hot air and operation noises from the indoor and outdoor units do not cause any inconvenience to your neighbours.

Do not leave any obstacles near the outlet and inlet of the outdoor unit. This may cause malfunctioning and increased operating noise.

If you hear an irregular noise during operation, contact your dealer.

Inspection and maintenance

Dependent upon service conditions and operating environment, the inside of the air-conditioner may become dirty after a number of seasons'
service (3 to 5 years). This will reduce performance. In addition to normal cleaning, we would recommend inspection and maintenance. (The air-
conditioner has a longer life without any trouble.)

Contact your dealer, or any distributor, for inspection and maintenance. (There will be a charge for this service).

We would recommend inspection and maintenance to be carried out during the off-season.

If the supply cord of this appliance is damaged, it must only be replaced by a repair shop appointed by the manufacturer, because special
purpose tools are required.

   Suitable installation position

Is there any obstruction in front of the indoor unit, preventing proper ventilation and functioning?

Don’t install the unit in any of the following places:

Where there is a danger of leaking inflammable gases.

Where there is substantial splashing of oil.

Malfunctioning due to corrosion may occur if the unit is installed in a spa where sulfide gases are generated, or in a seaside resort exposed to
sea breezes. Contact your dealer.

The air-conditioner and remote control must be at least 1 metre away from a TV set or radio.

Drain the dehumidified liquid from the indoor unit into a spot that drains well.

The air-conditioner does not work at all.

Has the timer been set in the
"ON" position?

Has the power switch been
turned off?

Is there a power failure or a
blown fuse?

Troubleshooting

Please carry out the following checks before making a service call.

Poor cooling

Did you leave any doors or
windows open?

Have you set the thermostat at a
suitable temperature?

Is there a heat source in the
room?

Are there too many people in
the room?

Is the air filter clean? (Not
clogged?)

suitable

temperature

Is there any direct sunlight en-
tering the room?

If the air-conditioner does not oper-
ate properly after you have checked
the left points, or if any doubt still
exists after you have consulted page
20, or if things happen as shown on
page 21, switch off the power and
contact your dealer.

Is the outdoor heat exchanger
clean? (Not clogged?)

RKW012A217_En.p65

06.8.3, 1:56 PM

19

Содержание SRK52CF-BN

























Отзывы: