background image

 

11

 

(b) Connecting a cable to the spring clamp terminal block 

The following explains connecting method of a cable to a spring clamp 
terminal block. 
For the stripping method of the cable end, refer to Section 5.3. in this 
manual. 
Use a recommended screwdriver or equivalent for connecting or 
disconnecting cables. 
For details of the driver, refer to Appendix.5 in the Q corresponding 
MELSECNET/H Network System Reference Manual (PLC to PLC 
network).  

1) Connecting the cable 

Fully insert the cable into the correct opening with the open/close 
button pressed by a slotted screwdriver. 
When using a bar terminal, the cable can be inserted without 
pressing the button. 

 

Insertion hole

Open/close button

 

 

2) Disconnecting the cable 

Keep pressing the open/close button by a slotted screwdriver until 
the cable is completely pulled out. 
 

5.2 Twisted Bus System (When using CC-Link Ver.1.10-compatible Cable) 

 

5.2.1 Specifications of CC-Link Ver. 1.10-compatible cable 

The following table shows the specifications of the CC-Link Ver. 1.10-compatible 
cable used for the twisted bus system. 
The following CC-Link Ver. 1.10-compatible cables can be used. 

 

Product name 

Model 

Manufacturer 

FANC-110SBH  

Mitsubishi Electric System & Service Co., 
Ltd. 

CC-Link Ver. 
1.10-compatible cables 

FA-CBL200PSBH 

Mitsubishi Electric Engineering Co., Ltd. 

 

Содержание QJ71NT11B

























Отзывы: