Mitsubishi Mr. Slim SLZ Series Скачать руководство пользователя страница 26

Страница: 26 / 30

9-4. FIXING HORIZONTAL VANE

Horizontal vane of each air outlet can be fixed according to the environment where it is installed.

Setting procedure

1) Turn off a main power supply (Turn off a breaker).
2) Remove the vane motor connector in the direction of the arrow shown below with pressing the unlocking button as in the

figure below.

Insulate the disconnected connector with the plastic tape.

Vane motor

Horizontal vane

Connector

Unlocking button

Vane motor

3) Set the vertical vane of the air outlet by hand slowly within the range in the table below.

Measured standard

position of the grille

Horizontal vane

< Specified range >

Up/down airflow

direction

Horizontal 30°

Downward 45°

Downward 55°

Downward 70°

21 mm

25 mm

28 mm

30 mm

The vanes can be set between 21mm and 30 mm.

Caution:

Do not set the up/down vanes passed the specified range. Condensation could form and drop from the ceiling,

or the unit could malfunction.

OCH493D

Содержание Mr. Slim SLZ Series































Результаты поиска

Содержание Mr. Slim SLZ Series

Отзывы:

Похожие инструкции для Mr. Slim SLZ Series

Бренды по названию

Популярные бренды

Mitsubishi Mr. Slim SLZ Series, Техническое и сервисное руководство

Результаты поиска

Содержание Mr. Slim SLZ Series

Отзывы:

Похожие инструкции для Mr. Slim SLZ Series

Бренды по названию

Популярные бренды