Mitsubishi Mr. Slim SLZ Series Скачать руководство пользователя страница 25

Страница: 25 / 30

4-WAY AIR FLOW SYSTEM

9-1. FRESH AIR INTAKE (LOCATION FOR INSTALLATION)

At the time of installation, use the duct holes (cut out) located at the positions shown in following diagram, as and when required.

Detail drawing of fresh air intake

Ceiling surface

Refrigerant pipe

Drain pipe

Electrical Box

Cut out hole

73.4

Burring hole

2.8 hole

100

120°

Fresh air intake

SLZ-KA25VAQ.TH SLZ-KA35VAQ.TH SLZ-KA50VAQ.TH
SLZ-KA25VAQR1.TH SLZ-KA35VAQR1.TH SLZ-KA50VAQR1.TH
SLZ-KA25VAQ2.TH SLZ-KA35VAQR2.TH SLZ-KA50VAQR2.TH

9-2. FRESH AIR INTAKE AMOUNT & STATIC PRESSURE CHARACTERISTICS

●

Whenever the indoor unit operates, the

duct fan operates.

(1) Connect the optional multiple

remote controller adapter (PAC-
SA88HA-E) to the connector CN51
on the indoor controller board.

(2) Drive the relay after connecting the

12V DC relay between the Yellow
and Orange connector wires.

Use a nonpolar relay of 1W or smaller.

MB: Electromagnetic switch power

relay for duct fan.

X: Auxiliary relay (12V DC LY-1F)

Multiple remote
controller adapter
PAC-SA88HA-E

Indoor controller board

Distance between indoor
controller board and relay
must be within 10m.

Be sure to secure insulation
material by tape, etc.

Green

Yellow

Orange

Connector (5P)

Indoor unit side

Multiple remote
controller adapter
PAC-SA88HA-E

Be sure to secure insulation
material by tape, etc.

Installation at site

CN51
on
indoor unit
board

Red

Brown

CN51

CN51(WHT)

9-3. OPERATION IN CONJUNCTION WITH DUCT FAN (BOOSTER FAN)

Static pressure : P [Pa]

Air flow : Q [m

/min]

-50

-100

-150

-200
-250

-300

0.5 1.0 1.5 2.0 2.5 3.0 3.5

Taking air into the unit

Curve in the
left graphs

Duct characteristics
at site

NOTE: Fresh air intake amount should be 20% or less of

whole air amount to prevent dew dripping.

How to read curves

Q…Designed amount of fresh air intake

/min>

A…Static pressure loss of fresh air

intake duct system with air flow
amount Q

<Pa>

B…Forced static pressure at air condi-

tioner inlet with air flow amount Q

<Pa>

C…Static pressure of booster fan with

air flow amount Q

<Pa>

D…Static pressure loss increase

amount of fresh air intake duct
system for air flow amount Q <Pa>

E…Static pressure of indoor unit with

air flow amount Q

<Pa>

Qa…Estimated amount of fresh air

intake without D

/min>

Unit : mm

OCH493D

Содержание Mr. Slim SLZ Series































Результаты поиска

Содержание Mr. Slim SLZ Series

Отзывы:

Похожие инструкции для Mr. Slim SLZ Series

Бренды по названию

Популярные бренды

Mitsubishi Mr. Slim SLZ Series, Техническое и сервисное руководство

Результаты поиска

Содержание Mr. Slim SLZ Series

Отзывы:

Похожие инструкции для Mr. Slim SLZ Series

Бренды по названию

Популярные бренды