REAR AXLE
LSD Case Assembly
r
Differential side
Differential
Differential
pinion mate
Thrust washer
Pinion mate
washer
1
(3) Insert the special tool at the spline part of differential
case B (right) and check to be sure the side gear (right)
rotates.
Then insert a 0.09 mm
in.) feeler gauge to
replace a 0.03 mm
in.) gauge.
Insert the special tool at the spline part of the
differential side gear (right) and check to be sure the
side gear (right) does not rotate.
Differential gear backlash
Standard value (clearance in thiust direction of
side gear): 0.03
0.09
m m
in.)
NOTE
If the clearance in the thrust direction of the side gear is
within the standard value range, the backlash of the
differential gear is normal.
(6) If the clearance in the thrust direction of the side gear is
not within the standard value range, remove differential
case A and make the adjustment by adjusting the
thickness of the thrust washer (left).
SERVICE POINTS OF DISASSEMBLY
3. REMOVAL OF THE THRUST WASHER (LEFT) 9.
THRUST WASHER (RIGHT)
The thrust washers (left and right) are of different thick-
ness, and so should be discriminated in some way for
reference during installation.
INSPECTION
Check the gears and differential pinion shaft for unusual
wear or damage.
(2) Check the spline part of the differential side gear (right) for
stepped wear or damage.
(3) Check the thrust washer and pinion mate washer for
unusual wear of contact surfaces, heat damage or other
damage.
(4) Check differential cases A and B for unusual wear of
contact surfaces, heat damage or other damage.
Contact surface with the viscous unit
Contact s ur ace
f
with the pinion mate washer
and
Contact surfaces with thrust washer
TSB Revision
Содержание 3000GT 1991
