Mitsubishi Electric PLK-J4040RH Скачать руководство пользователя страница 42

Страница: 42 / 60

- 36 -

7-5. Adjustment of the thread trimmer

When remove the component of the thread trimmer mechanism for maintenance, please refer to following

adjustment procedures.

7-5-1. Adjustment of the movable knife

(1) Remove the sliding plate (No.1) by referring to the paragraph <6-2-1>.

(2) Aligning the center of the trimmer link hole (No.2) with the reference hole (No.3) as below figure.

(3) Please confirm if the tip of movable knife (No.5) is on a virtual plane of the machining surface of sliding

plate (No.4) as below figure. In this time, keep aligning the center of the trimmer link hole (No.2) and

the reference hole (No.3).

(4) If different, loosen the screw (No.6) and adjust the tip of movable knife (No.5) position by moving in the

arrow direction. In this time, keep aligning the center of the trimmer link hole (No.2) and the reference

hole (No.3) too.

(5) After adjustment, tighten the screw (No.6) and reconfirm the tip of movable knife (No.5) position.

<1>:

Sliding plate <2>: Trimmer link hole <3>: Reference hole

<1>

<2>

<3>

<2>

<6>

<4>

<5>

(<4> Virtuality)

<4>:

Machining surface

<5>: Tip of movable knife

<6>: Screw

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

Содержание PLK-J4040RH





























































Результаты поиска

Содержание PLK-J4040RH

Отзывы:

Похожие инструкции для PLK-J4040RH

Бренды по названию

Популярные бренды

Mitsubishi Electric PLK-J4040RH, Техническое руководство

Результаты поиска

Содержание PLK-J4040RH

Отзывы:

Похожие инструкции для PLK-J4040RH

Бренды по названию

Популярные бренды