Mitsubishi Electric PLK-J4040RH Скачать руководство пользователя страница 22

Страница: 22 / 60

- 16 -

6-2. Adjustment of the position between the needle and the rotating hook

6-2-1. Adjustment of the clearance between the hook point and the needle

(1) Turn the power switch OFF.

(2) Open the bobbin access door.

(3) Remove the four screws (No.2) and remove the sliding plate (No.1). In this time, the trimmer link

(No.4) is removed from the driving lever (No.3).

NOTE The trimmer lever (No.4) is fitted with drive lever (No.3) by entering the locate pin witch have

driving lever (No.3) into the trimmer lever (No.4) hole. When remove the trimmer lever (No.4), hold the

trimmer lever (No.4) by hand as in the below drawing and lift the sliding plate (No.1). The trimmer link

(No.4) is removed from the driving lever (No.3) smoothly.

(4) To entering the locate pin witch have driving lever (No.3) into the trimmer lever (No.4) hole smoothly,

aligning the center of the trimmer link (No.4) hole with the reference hole (No.5) when back the sliding

plate (No.1).

<1>: Sliding plate <2>: Screw <3>: Driving lever <4>: Trimmer lever

<5>: Reference hole

<1>

<2>

<3>

<4>

<5>

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

Содержание PLK-J4040RH





























































Результаты поиска

Содержание PLK-J4040RH

Отзывы:

Похожие инструкции для PLK-J4040RH

Бренды по названию

Популярные бренды

Mitsubishi Electric PLK-J4040RH, Техническое руководство

Результаты поиска

Содержание PLK-J4040RH

Отзывы:

Похожие инструкции для PLK-J4040RH

Бренды по названию

Популярные бренды