Mitsubishi Electric PLK-J4040RH Скачать руководство пользователя страница 18

Страница: 18 / 60

- 12 -

5-7.How to operating the jig eject system

(1) Prepare the type of the work holder for jig eject system, and install the cassette jig right (No.1) and

cassette jig left (No.2) which are enclosed in accessory box.

NOTE For more information concerning about dimension, please refer to the last chapter <10-1.>.

(2) Install the cassette jig right (No.1) and cassette jig left (No.2) to the inmost part of the each jig eject

system (No.3).

(3) Step on the work holder (black colored) foot pedal. The work holder become fixed when both of locate

pin (No.4) which has each jig eject system actuated. Please make sure if the work holder is fixed

securely after step on the foot pedal. The work holder is not fixed due to the insufficient actuation of

locate pin (No.4) when either or both cassette jig are not installed enough.

NOTE Please make sure if the bottom surface of cassette jig (A) and lower plate (No.5) are in same level.

If different, loosen the each four of Jig eject system install screws (No.6) and adjust the jig eject system

(No.3) height.

NOTICE Please note that the lower plate (No.5) does not touch directly to the slide plate.

<1>: Cassette jig right <2>: Cassette jig left <3>: Jig eject system

<6>: Jig eject system install screw

<4>

<3>

<5>

<A>

<3>: Jig eject system

<4>: Locate pin

<5>: Lower plate

<A>: Bottom surface of cassette jig

<2>

<1>

”R” marking

”L” marking

<6>

<3>

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

Содержание PLK-J4040RH





























































Результаты поиска

Содержание PLK-J4040RH

Отзывы:

Похожие инструкции для PLK-J4040RH

Бренды по названию

Популярные бренды

Mitsubishi Electric PLK-J4040RH, Техническое руководство

Результаты поиска

Содержание PLK-J4040RH

Отзывы:

Похожие инструкции для PLK-J4040RH

Бренды по названию

Популярные бренды