background image

1

BH79J525H01

CITY MULTI Control System and Mitsubishi Mr. Slim Air Conditioners

Installation Manual

Wireless Remote Controller

PAR-SL100A-E

This installation manual contains only the description of how to install the wireless remote controller unit PAR-SL100A-E.
  

1 Safety Precautions

” described below thoroughly and then install the wireless remote controller unit PAR-

SL100A-E correctly.

        

           !

"# $%&'()**&+      !

1 Safety Precautions

 WARNING

This symbol denotes what could lead to serious injury or death if you misuse the PAR-SL100A-E.

 CAUTION

This symbol denotes what could lead to a personal injury or damage to your property if you misuse the PAR-SL100A-E.

 WARNING

Ask your dealer or technical representative to install the unit.

     
!

Install in a place which is strong enough to withstand the weight of the
PAR-SL100A-E.

   $%&'()**&+
personal injury.

Never modify or repair the PAR-SL100A-E by yourself.

    
!
Consult with your dealer about repairs.

 CAUTION

        

Flammable gases accumulated around the body of PAR-SL100A-E may cause
an explosion.

Do not use in any special environment.

Using in any place exposed to oil (including machine oil), steam and sulfuric 
     #  
component parts.

Do not wash with water.

4     !

Do not install in any place at a temperature of more than 40 °C (104 °F) or 
less than 0 °C (32 °F) or exposed to direct sunlight.

Ensure that installation work is done correctly following this installation 
manual.

     !

All electrical work must be performed by a licensed technician, accord-
ing to local regulations and the instructions given in this manual.

      
 !

Do not move and re-install the PAR-SL100A-E yourself.

     !
 ##   !

To dispose of this product, consult your dealer.

Do not install in any steamy place such a bathroom or kitchen.

Avoid any place where moisture is condensed into dew. Doing so may cause 
   !

Do not install in any place where acidic or alkaline solution or special 
spray are often used.

4    !

Do not touch any circuit board with your hands or with tools. Do not al-
low dust to collect on the circuit board.

4   !

Do not touch any control button with your wet hands.

4     !

Do not press any control button using a sharp object.

4     !

Содержание PAR-SL100A-E









Отзывы: