background image

6

3.Installation procedure [Applicable model : Group B]

 To protect the wires connected to M-NET board from the edges of sheet-metal 

component, paste the insulation on the edge surface of panel sheet-metal before 
proceeding with the following work.

Paste insulation sheet         on sheet-metal 
so that it completely envelops the edge 
surface of sheet-metal.

Install M-NET board     (with insulation 
sheets and supports) on the side of 
electrical parts box so that the rotary 
switches (SW11, SW12) faces up (at the 
four points indicated by arrows).
Note: Push it firmly until you hear it “click”.

Use terminal screw     to secure terminal 
block     .
Note:
Terminal block     has a round boss for 
positioning: Fit the round boss into the 
positioning hole in steel-plate.

(When viewed from the side of Electrical parts box)

(When viewed from the side of Electrical parts box)

Control board

M-NET board

Paste label     under terminal block     .

Use lead wire-A     to connect CN5 of 
M-NET board     connection and CNMNT of 
outdoor control board.

• Caution 

Wire Marking: INV type, 
Connector color: Red 
Always make sure that the markings and 
the applicable model match. If used 
incorrectly, parts could be damaged.

Use lead wire-C     to connect CND of 
M-NET board     connection and CNVMNT 
of outdoor control board.

Use lead wire-D     to connect CN2M of 
M-NET board     connection and terminals 
A and B of terminal block     Polarity is not a 
concern.
Note: 
Connect the wire firmly making sure that the 
screws on terminal block are not loose.

The lead wires should be tied together with 
the other lead wires with the fastener     
not to loose. 
Wiring length is adjusted according to 
apparatus.

Note1:
Use ground wire and screw     as required 
to connect the shield of M-NET transmission 
line to the unit.
(See the attention on page 2)
Note2: 
Take great care that no lead wire is caught 
on anything when installing panels.

Terminal block 
(M-NET)

Terminal screw 

(M3

o

20)

Label

Ground wire 
and screw 
(M4×8)

Insulation sheet

Lead wire-D

Содержание PAC-SJ95MA-E













Отзывы: