2-4. PIPE FORMING AND DRAIN PIPING
Pipe Forming
• Place the drain hose below the refrigerant piping.
0DNHVXUHWKDWWKHGUDLQKRVHLVQRWKHDYHGRUVQDNHG
• Do not pull the hose when applying the tape.
• When the drain hose passes the room, be sure to wrap
insulation material (obtainable at a store) around it.
2-1. FIXING OF INSTALLATION PLATE
)LQGDVWUXFWXUDOPDWHULDOVXFKDVDVWXGLQWKHZDOODQG¿[LQVWDOODWLRQSODWHKRUL
-
]RQWDOO\E\WLJKWHQLQJWKH¿[LQJVFUHZV¿UPO\
7RSUHYHQWLQVWDOODWLRQSODWHIURPYLEUDWLQJEHVXUHWRLQVWDOOWKH¿[LQJVFUHZVLQWKH
KROHVLQGLFDWHGLQWKHLOOXVWUDWLRQ)RUDGGHGVXSSRUW¿[LQJVFUHZVPD\DOVREHLQVWDOOHG
in other holes.
:KHQWKHNQRFNRXWLVUHPRYHGDSSO\YLQ\OWDSHWRWKHNQRFNRXWHGJHVWRSUHYHQWGDPDJ
-
ing the wires.
• When bolts recessed in the concrete wall are to be utilized, secure installation plate (1)
using 11 × 20 · 11 × 26 oval hole (450 mm pitch).
,IWKHUHFHVVHGEROWLVWRRORQJFKDQJHLWIRUDVKRUWHURQHDYDLODEOHLQWKHPDUNHW
2-2. WALL HOLE DRILLING
1) Determine the wall hole position.
2) Drill a ø75 mm hole. The outdoor side should be
5 to 7 mm lower than the indoor side.
3) Insert wall hole sleeve (C).
2-3. CONNECTING WIRES FOR INDOOR UNIT
You can connect indoor/outdoor unit connecting wire (A) without removing the front panel.
1) Open the front panel.
2) Remove electrical cover.
3) Remove VA clamp.
3DVVLQGRRURXWGRRUXQLWFRQQHFWLQJZLUH$IURPWKHEDFNRIWKHLQGRRUXQLWDQGSURFHVV
the end of the wire.
/RRVHQWHUPLQDOVFUHZDQGFRQQHFW¿UVWWKHHDUWKZLUHWKHQLQGRRURXWGRRUXQLWFRQ
-
QHFWLQJZLUH$WRWKHWHUPLQDOEORFN%HFDUHIXOQRWWRPDNHPLVZLULQJ)L[WKHZLUHWR
WKHWHUPLQDOEORFNVHFXUHO\VRWKDWQRSDUWRILWVFRUHLVDSSHDUHGDQGQRH[WHUQDOIRUFH
LVFRQYH\HGWRWKHFRQQHFWLQJVHFWLRQRIWKHWHUPLQDOEORFN
6) Replace the VA clamp and electrical cover securely.
2. INDOOR UNIT INSTALLATION
Rear, right, or downward piping
1) Put the refrigerant piping and the drain hose
WRJHWKHUWKHQ¿UPO\DSSO\SLSLQJWDSH*IURP
the end.
2) Insert the piping and the drain hose into the wall
KROHVOHHYH&DQGKRRNWKHXSSHUSDUWRIWKH
indoor unit on the installation plate (1).
&KHFNLIWKHLQGRRUXQLWLVKRRNHGVHFXUHO\RQWKHLQVWDOODWLRQSODWHE\PRYLQJ
the unit to left and right.
4) Thrust the lower part of the indoor unit into the installation plate (1).
Drain Piping
• If the extension drain hose has to pass through a room, be sure to wrap it with commer-
cially sold insulation.
7KHGUDLQKRVHVKRXOGSRLQWGRZQZDUGIRUHDV\GUDLQÀRZ)LJ
• If the drain hose provided with the indoor unit is too short, connect it with drain hose (I)
that should be provided at your site. (Fig. 2)
• When connecting the drain hose to the hard vinyl chloride pipe, be sure to insert it securely
into the pipe. (Fig. 3)
'RQRWPDNHGUDLQSLSLQJDVVKRZQEHORZ
Do not raise
Accumulated
drain water
Air
Waving
Water
OHDNDJH
Water
OHDNDJH
Water
OHDNDJH
Tip of drain
hose dipped
in water
Ditch
At least
50 mm
gap
Cut off in case of
right piping.
Cut off in case of
downward piping.
Downward
slope
Drain
hose
Soft hose
I.D. 15 mm
Drain hose
Hard vinyl chloride
pipe I.D. 30 mm
Insert
securely
Different
diameter joint
70 cm
or more
Fig. 1
Fig. 2
Fig. 3
• For future servicing, give extra length to
the connecting wires.
0DNHHDUWKZLUHDOLWWOHORQJHUWKDQRWKHUV
(More than 60 mm)
• Do not fold the excess wire, or cram it into
VPDOOVSDFH7DNHFDXWLRQQRWWRGDPDJH
the wires.
• Be sure to attach each screw to its cor-
respondent terminal when securing the
FRUGDQGRUWKHZLUHWRWKHWHUPLQDOEORFN
Note:
Do not place the wires between the
indoor unit and the installation plate (1).
Damaged wire could cause heat genera-
WLRQRU¿UH
Wall
Outdoor
side
ø75 mm
5-7 mm
,QGRRUWHUPLQDOEORFN
Indoor/outdoor
unit
connecting wire
(A)
2XWGRRUWHUPLQDOEORFN
Earth wire
(green/yellow)
Lead wire
15 mm
55 mm
Installation plate (1)
Center of
ø 75 mm hole
220 mm
or more
120 mm
or more
Ceiling
Wall
Fixing screw (2)
* Same for left hole.
Insert
the
scale. *
Align the
scale with
the line. *
Level
72 mm or more/
130 mm or more
for left/left rear
piping (using
spacer)
100 mm
Wall
In the case of left or left rear piping.
7KHSRVLWLRQRIWKH/LTXLG*DVSLSH
union is shifted 56/40 mm to the left
IURPWKHPDUN
7HUPLQDOEORFN
Fixing screws
Indoor/outdoor unit connecting wire (A)
VA clamp
Electrical cover
/LTXLGSLSH
Gas pipe
Felt tape (4)
Indoor/outdoor
unit connecting
wire (A)
Piping tape (G)
1) Put the refrigerant piping and the drain hose together, then
¿UPO\DSSO\IHOWWDSHIURPWKHHQG
Felt tape (4) overlap width should be 1/3 the tape width.
Use a bandage stopper at the end of felt tape (4).
2) Pull out the drain cap at the rear right of the indoor unit.
(Fig. 1)
• Hold the convex section at the end and pull the drain cap.
3) Pull out the drain hose at the rear left of the indoor unit.
(Fig. 2)
+ROGWKHFODZPDUNHGE\WKHDUURZVDQGSXOORXWWKH
drain hose forward.
4) Put the drain cap into the section to which the drain
hose is to be attached at the rear of the indoor unit.
(Fig. 3)
• Insert not sharp-edged tools such as screwdrivers into
the hole at the end of the cap and insert the cap fully
into the drain pan.
5) Insert the drain hose fully into the drain pan at the rear right
of the indoor unit. (Fig. 4)
&KHFNLIWKHKRVHLVKRRNHGVHFXUHO\WRWKHSURMHFWLRQ
of its inserting part at the drain pan.
,QVHUWWKHGUDLQKRVHLQWRZDOOKROHVOHHYH&DQGKRRN
the upper part of indoor unit on installation plate (1). Then,
PRYHWKHLQGRRUXQLWFRPSOHWHO\WRWKHOHIWLQRUGHUWRPDNH
SODFLQJWKHSLSLQJLQWKHEDFNVSDFHRIWKHXQLWHDVLHU
7) Cut out 2 pieces of cardboard from the shipping box (use
DQ\WZRSLHFHVRIWKHIRXUSLHFHVUROOHDFKSLHFHKRRN
WKHPRQWRWKHEDFNULEDQGXVHWKHPDVVSDFHUWROLIWWKH
indoor unit. (Fig. 5)
8) Connect the refrigerant piping with the extension pipe (B).
9) Thrust the lower part of the indoor unit into the installation
plate (1).
Left or left-rear piping
Note:
Be sure to reattach the drain hose and
the drain cap in case of left or left-rear
piping.
Otherwise, it could cause drops of water
to drip down from the drain hose.
Piping tape (G)
Felt tape (4)
Cut off in case of
left piping.
Drain cap
Drain cap
Drain hose
Drain cap
Drain hose
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
