Mitsubishi Electric Mr.SLIM PE-3EAK Скачать руководство пользователя страница 24

Страница: 24 / 64

Errors detected by indoor unit

• On wired remote controller

Check code displayed in the LCD.

Symptom

Cause

Wired remote controller

PLEASE WAIT

→

Error code

Display messages do not
appear even when operation
switch is turned ON (operation
lamp does not light up).

For about 2
minutes follow-
ing power-on

After about 2
minutes has
expired follow-
ing power-on

• For about 2 minutes following power-on,op-

eration of the remote controller is not possible
due to system start-up. (Correct operation)

• Connector for the outdoor unit’s protection

device is not connected.

• Reverse or open phase wiring for the outdoor

unit’s power terminal block

• Incorrect wiring between indoor and outdoor

units

• Remote controller wire short

Note:
Operation is not possible for about 30 seconds after cancellation of function selection. (Correct operation)

For description of each LED (LED1, 2) provided on the indoor controller, refer to the following table.

LED1 (power for microcomputer)

Indicates whether control power is supplied. Make sure that this LED is
always lit.

LED2 (power for wired remote controller)

Indicates whether power is supplied to the wired remote controller.
This LED lights only in the case of the main indoor unit.

• If the unit cannot be operated properly after test run has been performed, refer to the following table to remove the cause.

Check code

Symptom

Remark

Wired remote controller

Intake sensor error

Pipe (TH2) sensor error

Drain sensor error

P5
PA

Drain pump error
Forced compressor stop

Freezing/ Overheating safeguard operation

Pipe temperature error / Outdoor unit error

E4, E5

Remote controller signal receiving error

–

Indoor unit control system error (memory error, etc.)

E0, E3
E1, E2

Remote controller control board error

Remote controller transmission error

OC394--1.qxp 06.5.23 5:44 PM Page 24

Содержание Mr.SLIM PE-3EAK

































































Результаты поиска

Содержание Mr.SLIM PE-3EAK

Отзывы:

Похожие инструкции для Mr.SLIM PE-3EAK

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr.SLIM PE-3EAK, Техническое и сервисное руководство

Результаты поиска

Содержание Mr.SLIM PE-3EAK

Отзывы:

Похожие инструкции для Mr.SLIM PE-3EAK

Бренды по названию

Популярные бренды