Mitsubishi Electric MR. SLIM PCA Series Скачать руководство пользователя страница 9

Страница: 9 / 52

OCH659A

3-2. WIRELESS

REMOTE CONTROLLER (OPTION)

ON/OFF

TEMP

FAN

VANE

TEST RUN

AUTO STOP

AUTO START

min

LOUVER

MODE

CHECK

RESET

SET

CLOCK

MODEL SELECT

NOT AVAILABLE

CHECK TEST RUN

°C

AMPM

VANE CONTROL button

Used to change the airflow direction.

CLOCK button

RESET button

SET button

ON/OFF button

The unit is turned ON and OFF alternately

each time

the button is pressed.

MODE SELECT button

Used to switch the operation mode between

cooling, drying, heating, auto and fan mode.

CHECK-TEST RUN buttons

Only press this button to perform an

inspection check or test operation.

Do not use it for normal operation.

FAN SPEED SELECT button

Used to change the fan speed.

TIMER display

Displays when in timer operation or when

setting timer.

buttons

SET TEMPERATURE button sets any desired

room temperature.

CLOCK display

Displays the current time.

“ ” “ ” display

Displays the order of timer operation.

“ ” “ ” display

Displays whether timer is on or off.

Buttons used to set the “hour and minute” of

the current time and timer settings.

“h” and “min” buttons

display

FAN SPEED display indicates which fan

speed has been selected.

display

The vertical direction of airflow is indicated.

display

Blinks when model is selected.

display

CHECK and TEST RUN display indicate that

the unit is being checked or test-run.

display

OPERATION MODE display

Operation mode display indicates which

operation mode is in effect.

AUTO STOP (OFF timer): when this switch

is set, the air conditioner will be

automatically stopped at the preset time.

AUTO START (ON timer): when this switch is

set, the air conditioner will be automatically

started at the preset time.

MODEL SELECT

CHECK TEST RUN

LOUVER button

Changes left/right airflow direction.
(Not available for this model.)

SET TEMP. display indicates the desired

temperature which is set.

Lights up while the signal is transmitted to

the indoor unit when the button is pressed.

TIMER CONTROL buttons

The functions which can be used are restricted according to each model.

Содержание MR. SLIM PCA Series





















































Результаты поиска

Содержание MR. SLIM PCA Series

Отзывы:

Похожие инструкции для MR. SLIM PCA Series

Бренды по названию

Популярные бренды

Mitsubishi Electric MR. SLIM PCA Series, Руководство по обслуживанию

Результаты поиска

Содержание MR. SLIM PCA Series

Отзывы:

Похожие инструкции для MR. SLIM PCA Series

Бренды по названию

Популярные бренды