Mitsubishi Electric MR. SLIM PCA Series Скачать руководство пользователя страница 48

Страница: 48 / 52

OCH659A

OPERATING PROCEDURE

PHOTOS & FIGURES

Screws

Side panel

(Right)

Side panel

(Left)

Sliding the panel

to the front

Figure 3

6. Removing the side panel

(1) Remove the air intake grille. (See Figure 1, 2)

(2) Remove the screws from the side panel, and remove

the side panel by sliding the panel to the front.

(3) Unhook the side panel support hanger, and then slide

the side panel forward to remove it.

5. Removing the fan (3 connection)

(1) Remove the air intake grille. (See Figure 1, 2)

(2) Remove the beam by removing screws. (See Photo 1)

(3) Remove 2 screws from the electrical cover, and remove

the electrical cover.

(4) Remove 2 screws from the electrical box and pull the

electrical box downward.

Temporarily secure the electrical box using 2 hooks in

the back of electrical box.

(5) Remove 4 screws from the fan guard of the fan motor.

(See Photo 5)

(6) Remove 2 screws from the left side beam and remove

the beam. (See Photo 1)

(7) Remove the 3 screws from center fan guard and remove

the fan guard. (2 screws : See Photo 9 / 1 screw : Drain

pan side)

(8) Remove 2 screws from the left fan guard and remove

the fan guard. (See Photo 10)

(9) Loosen 2 set screws (2 hexagon set screws) of connect-

ing joint. (See Photo 5)

(10) Remove 3 lower casings while pressing each 4 catches

of the casing.

(11) Remove the 4 screws from the bearing support. (See

Photo 11)

(12) Slide the connecting joint to the left and remove the fans

and shaft together. (See Photo 12)

(13) Remove the fan from the shaft. (See Photo 7, 8)

Photo 9

Beam

Electrical box

Fan guard

fixing screws

Photo 10

Fan guard

fixing screws

Photo 11

Bearing sup-

port fixing

screws

Bearing support

Shaft

Photo 12

Fans (3 connection)

Bearing support

Shaft

Side panel

support hanger

Hole for side panel

support hanger

Figure 4

Содержание MR. SLIM PCA Series





















































Результаты поиска

Содержание MR. SLIM PCA Series

Отзывы:

Похожие инструкции для MR. SLIM PCA Series

Бренды по названию

Популярные бренды

Mitsubishi Electric MR. SLIM PCA Series, Руководство по обслуживанию

Результаты поиска

Содержание MR. SLIM PCA Series

Отзывы:

Похожие инструкции для MR. SLIM PCA Series

Бренды по названию

Популярные бренды