6
5. Operation
<To Stop Operation>
■
Press the ON/OFF button
1
again.
• The ON lamp
1
and the display area go dark.
Note:
Even if you press the ON/OFF button immediately after shutting down the op
-
eration is progress, the air conditioner will not start for about 3 minutes.
This is to prevent the internal components from being damaged.
5.2. Mode select
5.2.1. For wired remote-controller
■
Press the operation mode (
) button
2
and select the opera-
tion mode
2
.
Cooling mode
Drying mode
Fan mode
Ventilation mode
Only indicated on the following condition
Wired remote controller used
LOSSNAY connected
Note:
The heating display and the automatic display does not appear in models that
operate exclusively as cooling only air-conditioner.
5.2.2. For wireless remote-controller of cooling only type
Cooling mode
Drying mode
Fan mode
5.3. Temperature setting
►
To decrease the room temperature:
Press button
3
to set the desired temperature.
The selected temperature is displayed
3
.
►
To increase the room temperature:
Press button
3
to set the desired temperature.
The selected temperature is displayed
3
.
• Available temperature ranges are as follows:
Cooling/Drying: 19 - 30 °C
• The display blinks either 8 °C or 39 °C to inform you if the room tem-
perature is lower or higher than the displayed temperature.
(This display does not appear on the wireless remote controller.)
5.4. Fan speed setting
■
Press the Fan Speed button
5
as many times as necessary while the
system is running.
• Each press changes the force. The currently selected speed is
shown at
5
.
• The change sequence, and the available settings, are as follows.
FAN SPEED
Display
4-speed
+
Auto
Note:
●
The number of available fan speeds depends on the type of unit connected.
●
In the following cases, the actual fan speed generated by the unit will differ
from the speed shown the remote controller display.
1. When the unit is in DRY mode.
5.5. Airflow direction setting
<To Change the Airflow’s Up/Down Direction>
■
With the unit running, press the Airflow Up/Down button
6
as neces-
sary.
• Each press changes the direction. The current direction is shown at
6
.
• The change sequence and the available settings are as follows.
Remote controller
Display
Wired type
Swing Auto
1
2
3
4
5
Wireless type
Swing
2
3
4
1
* Note that during swing operation, the directional indication on the
screen does not change in sync with the directional vanes on the unit.
Note:
●
Available directions depend on the type of unit connected.
< How to set the fixed up/down air direction (Only for
wired remote controller and PUY application) >
Note:
●
This function cannot be set depending on the outdoor unit to be connected.
• For PLY-P.BA series, only the particular outlet can be fixed to certain
direction with the procedures below. Once fixed, only the set outlet is
fixed every time air conditioner is turned on. (Other outlets follow UP/
DOWN air direction setting of remote controller.)
■
Explanation of word
• “Refrigerant address No.” and “Unit No.” are the numbers given to
each air conditioner.
• “Outlet No.” is the number given to each outlet of air conditioner.
(Refer to the illustration below.)
•
“Up/Down air direction” is the direction (angle) to fix.
Speed 1
Speed 2
Speed 3
Speed 4
Auto
Horizontal airflow
Downward
Fixing
The airflow direction of
this outlet is fixed
in particular direction.
Remote controller setting
The airflow direction of
this outlet is controlled by
the airflow direction setting of
remote controller.
MITSUBISHI
ELECTRIC
label
Outlet No.4
Outlet No.2
Outlet No.3
Outlet No.1
Note: "0" indicates all outlets.
* When it is cold because of direct
airflow, the airflow direction can
be fixed horizontally to avoid
direct airflow.
Reset
1
horizontal
2
3
4
5
RG79Y555H02_en.indd 6
2016/06/10 8:56:48
