O
When 220 ~ 240V is not supplied, check the following points.
Error Mode Display
—19—
Confirm that 220~ 240V is supplied between TAB1 and TAB2
of control circuit.
Confirm that the relay connector of power switch lead wire is
not disconnected. (In the power switch case)
Disconnected
relay connector
Description of the error mode display
Cause
Check Method and Remedy
(No display. No Operation.)
Confirmation of
power supply
voltage
Confirm that the power switch is turned ON and that
220~ 240V is supplied at both ends of power cord connection
on the terminal block.
Q
When 220~ 240V is not supplied, check the following points.
1
Check if the earth leakage breaker is turned ON.
2
Check if the power cord is connected securely to the
terminal block.
Confirmation of
power supply voltage
on the control circuit
Measure the resistance between Blue-Orange wires and Brown-
Orange wires on the relay connector of power switch lead wire.
Defective power
switch
Switch (Power)
Relay connector
Orange
Blue
Blue
Brown
Tester
Brown
Orange
Orange
Orange
side
side
Power
O
Heater
O
Check
O
Blue LED
O
O
: ON
: Slow flicker (ON for 0.4 seconds/ OFF for 0.4 seconds)
O
: OFF
: Quick flicker (ON for 0.1 second/OFF for 0.1 second)
Troubles with error display
Power
Heater Check Blue LED
Switch (Power) “ON” : 0
Ω
Switch (Power) “OFF” :
∞
Ω
10. Troubleshooting
Q
Work precautions
• Before starting the service, try to reproduce the malfunction two or three times.
• When servicing, always take care to keep proper footing.
• Before starting the service, always unplug the power cord from the outlet, or turn off the earth leakage breaker
when no power cord plug is provided. Sufficient care must be taken to avoid electric shock or injury.
• Make sure to connect the power supply wires correctly.
• When removing a circuit board, hold the side of the board to avoid exerting any undue stress on parts on the board.
• When removing a circuit board, take care not to injure any body parts with the sharp edges of the metal sheet.
• When disconnecting connectors, don’t hold the lead wire to pull. Instead, hold the whole housing section.
• When circuit board failure is considered to be cause, check closely for any broken section on the copper foil
patterns, burning or discoloration of parts.
• After replacing a circuit board, make sure to restore the same settings as before the replacement.
@
The part names used in the following text correspond to those listed in the parts catalog.
Содержание JT-SB216ESH-DG-CE
