Mitsubishi Electric DX-TL4U Скачать руководство пользователя

Страница: 31 / 92

Four-Channel Digital Video Recorder

Figure 29 — System Check (Alarm Out / Notify) screen.

Highlight the box under the

Alarm Out

heading and press the button. A drop menu displays

available alarm outputs for the recording problem. Highlight the desired alarm output from the
external alarm out terminal or internal buzzer, and press the button.

NOTE:

Alarm Out

cannot be set to Check Point –

System

Highlight the box under

Notify

and press the

button. This toggles between

and

Off

. When it

, the DVR notifies the remote site of its

System (Good)

and

Record (Bad)

Storage Screen

Highlight

Storage

in the Main menu and press the button. The

Storage

setup screen appears.

Figure 30 — Storage screen.

The

Type

field displays the type and capacity of storage device.

The

Status

field displays the device status or fault conditions. (

Good, Disk Bad, S.M.A.R.T.

Alert, High Temperature,

Not installed)

Содержание DX-TL4U





























































































Результаты поиска

Содержание DX-TL4U

Отзывы:

Похожие инструкции для DX-TL4U

Бренды по названию

Популярные бренды

Mitsubishi Electric DX-TL4U, Руководство пользователя

Результаты поиска

Содержание DX-TL4U

Отзывы:

Похожие инструкции для DX-TL4U

Бренды по названию

Популярные бренды