Mitsubishi Electric City Multi PLFY-P15VCM-E3 Скачать руководство пользователя страница 31

Страница: 31 / 32

OPERATING PROCEDURE

PHOTOS & ILLUSTRATIONS

10. Removing the heat exchanger

(1) Remove the panel. (Refer to procedure 3 )

(2) Remove the drain pan. (Refer to procedure 6)

(3) Remove the nut and the washer from the turbo fan, and

remove the turbo fan.

(4) Remove the 2 screws fixed to the control box cover, and

remove the control box cover.

(5) Disconnect the connector of the FAN from the indoor con-

troller board.

(6) Remove the 3 screws fixed to the piping cover, and remove

the piping cover. (See Photo 9)

(7) Remove the pipe temperature thermistor/liquid and

condenser/evaporator temperature thermistor.

(Refer to procedure 7)

(8) Disconnect the lead wires to the direction of the fan motor.

(9) Remove the 1 coil support screw, the 2 inside coil screws

(See Photo 10), and the 4 outside coil screws (See Photo 9)

from the heat exchanger, and remove the heat exchanger.

9. Removing the drain pump (DP) and drain sensor (DS)

(1) Remove the panel. (Refer to procedure 3 )

(2) Remove the drain pan. (Refer to procedure 6)

(3) Remove the 2 screws fixed to the control box cover, and

remove the control box cover.

(4) Remove the connectors of the (CNP) and the (CN31)

from the indoor controller board.

(5) Remove the 1 screw fixed to the cover, and remove the

cover.

(6) Disconnect the lead wires to the direction of the drain

pump. (See Photo 7)

(7) Remove the 3 screws of the drain pump.

(8) Cut the drain hose band, pull out the drain hose from the

drain pump.

(9) Pull out the drain pump.

(10) Remove the drain sensor and the holder.

Photo 7

Screw

Screws

Drain sensor (DS)

Drain pump (DP)

Drain

hose

Fixing band

Photo 9

Photo 10

Control box

Cover

Screw

Control

box

Photo 8

Screws of

piping cover

Control box

Piping cover

Lead wires

Coil

screws

Heat exchanger

Coil

screws

Coil

support

Coil support screw

OCH569

Содержание City Multi PLFY-P15VCM-E3

































Результаты поиска

Содержание City Multi PLFY-P15VCM-E3

Отзывы:

Похожие инструкции для City Multi PLFY-P15VCM-E3

Бренды по названию

Популярные бренды

Mitsubishi Electric City Multi PLFY-P15VCM-E3, Техническое и сервисное руководство

Результаты поиска

Содержание City Multi PLFY-P15VCM-E3

Отзывы:

Похожие инструкции для City Multi PLFY-P15VCM-E3

Бренды по названию

Популярные бренды