MITSUBISHI ELECTRIC ENGINEERING PLA-RP-BA Series Скачать руководство пользователя страница 13

Страница: 13 / 220

Manual vane angle

Input display:

Cur.

Address

Check

Ref. address

Unit No.

Identify unit Check button

Manual vane angle

Input display:

Ref. address

Unit No.

The air conditioner with the

vane pointing downward is

the target air conditioner.

Manual vane angle

Input display:

There is no response from

the target device.

Confirm the state of the air

conditioner.

Confirmation procedure

First, confirm by setting “Ref. address” to 0 and “Unit No.” to 1.

• Move the cursor to "Ref. address" or "Unit No." with the [F1] button to select.

• Select the refrigerant address and the unit number for the units to whose

vanes are to be fixed, with the [F2] or [F3] button, and press the [SELECT]

button.

• Ref. address: Refrigerant address

• Unit No.: 1, 2, 3, 4

Press the [F4] button to confirm the unit.

Change the “Unit No.” in order and check each unit.

• Press the [F1] button to select “Unit No.”.

Press the [F2] or [F3] button to change the “Unit No.” to the unit that you want

to check, and then press the [F4] button.

• After pressing the [F4] button, wait approximately 15 seconds, and then check

the current state of the air conditioner.

→ The vane is pointing downward. → This air conditioner is displayed on the

remote controller.

→ All outlets are closed. → Press the [RETURN] button and continue the op

eration from the beginning.

→ The messages shown to the left are displayed. → The target device does

not exist at this refrigerant address.

• Press the [RETURN] button to return to the initial screen.

Change the “Ref. address” to the next number.

• Refer to step

to change the “Ref. address” and continue with the confirma

tion.

6. Electrical work

7. Test run

7.1. Before test run

► After completing installation and the wiring and piping of the indoor and

outdoor units, check for refrigerant leakage, looseness in the power sup-

ply or control wiring, wrong polarity, and no disconnection of one phase

in the supply.

► Use a 500-volt megohmmeter to check that the resistance between the

power supply terminals and ground is at least 1.0 MΩ.

► Do not carry out this test on the control wiring (low voltage circuit) termi

nals.

Warning:

Do not use the air conditioner if the insulation resistance is less than 1.0 MΩ.

7.. Test run

7..1. Using wired remote controller.

■ Make sure to read operation manual before test run. (Especially items to secure safety)

Step 1

Turn on the power.

● Remote controller: The system will go into startup mode, and the remote controller power lamp (green) and “PLEASE WAIT” will blink. While the lamp and message

are blinking, the remote controller cannot be operated. Wait until “PLEASE WAIT” is not displayed before operating the remote controller. After the power is turned on,

“PLEASE WAIT” will be displayed for approximately 2 minutes.

● Indoor controller board: LED 1 will be lit up, LED 2 will be lit up (if the address is 0) or off (if the address is not 0), and LED 3 will blink.

● Outdoor controller board: LED 1 (green) and LED 2 (red) will be lit up. (After the startup mode of the system finishes, LED 2 will be turned off.) If the outdoor controller

board uses a digital display, [- ] and [ -] will be displayed alternately every second.

If the operations do not function correctly after the procedures in step 2 and thereafter are performed, the following causes should be considered and eliminated if they

are found.

(The symptoms below occur during the test run mode. “Startup” in the table means the LED display written above.)

Symptoms in test run mode

Cause

Remote Controller Display

OUTDOOR BOARD LED Display

< > indicates digital display.

Remote controller displays “PLEASE WAIT”,

and cannot be operated.

After “startup” is displayed, only green lights up.

<00>

• After power is turned on, “PLEASE WAIT” is displayed for 2