manualshive.com logo in svg

Mitel Mediatrix Model M, Руководство по установке оборудования

Поделиться
Скачать
Mitel Mediatrix Model M Скачать руководство пользователя страница 34

GX Gateway Hardware Installation Guide

 

34

 

 

 

 
 

Federal Communications Commission (FCC) Disclaimer

 

 

This device complies with Part 15 of the FCC Rules. 
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in 
a particular installation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures:

 

• 

Reorient or relocate the receiving antenna.

 

• 

Increase the separation between the equipment and receiver. 

• 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected. 

• 

Consult the dealer or an experienced radio/television technician for help. 

 

IMPORTANT

: 

Modifications: Any modifications made to this device that are not approved by Mitel may void the 

authority granted to the user by the FCC to operate this equipment. 

 

Supplier's Declaration of conformity 

47 CFR § 2.1077 Compliance Information 

Unique Identifier 

Mediatrix Model M 

Responsible Party –U.S. Contact 
Information 

207 Beach Avenue, Kennebunk, Maine. 
04043 USA 

Email 

[email protected] 

FCC Compliance Statement 

This device complies with Part 15 of the FCC 
Rules. Operation is subject  to the following 
two conditions: 
(1) This device may not cause harmful 
interference, and 
(2) this device must accept any interference 
received, including interference that may 
cause undesired operation 

Содержание Mediatrix Model M









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды