manualshive.com logo in svg

Mitel CPDM3, Руководство по установке

Поделиться
Скачать
Mitel CPDM3 Скачать руководство пользователя страница 30

TD 

34/1531-ANF901 43 B1 2016-03-31

Installation Guide

27

1

Set the product in Boot Mode, see 

5.1 Set Product in Boot Mode 

on page 25.

2

Select Software > Install software.

3

Click the “Browse...” and locate the software (.pkg) file to install.

4

Select where to save the software. If two versions of the software already have 
been installed on the module choose which software to replace.

5

Select if the product shall be restarted after the installation or not.

6

If “Restart after installation” is selected, choose if the last used settings or the 
factory default settings shall be applied on the new software.

If you choose “Do not restart”, you can later, when returning to normal operation, 
choose and apply settings to software that is installed but not yet started.

NOTE: If current parameters cannot be used, i.e. if software of another type has been 

installed, factory default parameters will always be used.

7

Click the “Install Software” button.

8

If “Do not restart” is selected a dialog window is shown. Click “OK”.

5.1.4 RETURN TO NORMAL OPERATION

1

Click “Normal Operation”.

2

Select which software to start and click “OK”.

3

Select which settings to use for the software and click “OK”. The product will 
restart and return to normal operation.

Содержание CPDM3





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды