manualshive.com logo in svg

Mitel CPDM3, Руководство по установке

Поделиться
Скачать
Mitel CPDM3 Скачать руководство пользователя страница 12

TD 

34/1531-ANF901 43 B1 2016-03-31

Installation Guide

9

3.4 OPERATING MODE

Besides normal operation the product can be operated in three other modes, that is, 
Boot Mode, Demonstration Mode and Troubleshoot Mode.

3.4.1 NORMAL OPERATION

All configuration and settings for the product’s software, such as maintenance, software 
upgrade and troubleshooting, are performed in the web user interface described in the 
product’s user documentation.

3.4.2 BOOT MODE

If the software cannot be accessed, the product can be set in Boot Mode from the web 
user interface. From this interface, it is possible to install new software, start 
Troubleshoot Mode, see settings and to reset the module back to factory default 
settings

1

.

Placing the product in Boot Mode is performed manually by the user but if the product 
detects several major errors the module can place itself in Boot Mode.

1. Network settings such (IP address, Host name, etc.) will not be changed when resetting back to factory default.

* also used if the Power parameter conflicts with the actual setup.

Red

Red

Blue

Blue

Yellow

Yellow

Status LED

Blue

Mode LED

Blue

Blue

Yellow

Yellow

Blue

Status OK

Starting up/shutting down

Feedback 

(1 sec.)

Error/fault

Warning

Boot mode

Demonstation mode

Waiting for automatic
startup (1 min.)

Troubleshoot mode and
during firmware upgrade

Mass storage mode

Standby module synchronized 

Standby module during 
synchronization 

Yellow

Power LED

Blue

Blue

Yellow

Status LED

Mode LED

Blue

Blue

Confirmation is done and settings
can be activated

Secured settings

Indicates that manual confirmation is required

Red

Power LED

Closing down caused by
low voltage

Power

Power OK

Blue

Red

Low voltage*

Active module during 
synchronization 

Active module synchronized  

Blue

Blue

Red

Blue

Содержание CPDM3





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды