manualshive.com logo in svg

Mitel CPDM3, Руководство по установке

Поделиться
Скачать
Mitel CPDM3 Скачать руководство пользователя страница 28

TD 

34/1531-ANF901 43 B1 2016-03-31

Installation Guide

25

5. WORKING IN BOOT MODE

If the software installed on the product cannot be started, the Boot Mode can be used 
for installing new software, see settings, performing factory reset, troubleshooting and 
also starting up in normal operation again. If the product detects several major errors 
(for example restart loop), the product can set itself in Boot Mode.

5.1 SET PRODUCT IN BOOT MODE

The description below starts with a controlled restart. The operation takes 
approximately 5 minutes.

1

Press the Restart button and release it within 4 seconds (use a paper clip or 
similar). 

The status LED will first indicate shutting down with quick flashing blue light 

and then “waiting” with flashing yellow light 

.

2

Wait for one minute until the status LED indicates starting up with quick flashing 
blue light 

, then press the Mode button.

The Mode button LED will lit and show fixed blue light 

.

3

Then wait until the status LED changes to quick flashing yellow light 

, 

which indicates that the module has started in Boot Mode (after approximately 
one minute).

4

Enter the product’s IP address in a web browser.

If this operation does not work, pressing the mode button after an initiated forced 
restart can be used as a last resource, see 

7.2.2 Forced Restart 

on page 30.

5.1.1 SYSTEM INFORMATION

Under System > Information the reason for why the product is in Boot Mode, the 
module key number, MAC address, Boot software version, etc. are shown.

Figure 12. System information in Boot Mode.

Содержание CPDM3





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды