manualshive.com logo in svg

MITECH MR200, Руководство пользователя

Поделиться
Скачать
MITECH MR200 Скачать руководство пользователя страница 7

6

[email protected]

3.3 Battery Charging

When MR200 appears the low voltage tips or could not boot, it should be charging to the promptly. When

charging, put the charger into the micro-USB port, then put the charger into the socket. This instrument

adopts Li-poly battery, without memory effect, could be charged at any time. Red light indicates charging,

the green light indicates charging finished. The complete charging time is approximate 3-4 hours. It may

damage the battery for charging long time. When the instrument leaves the factory, the battery switch is

off.

3.4 Parameter Setting

In the main interface, press "Settings button" enter the main menu

Main Interface

3.4.1Measuring Conditions Setting

Measurement conditions setting by two ways: Quick settings and Menu settings.

Quick Setting: In the main menu, press "Settings button" enter quick setup mode, follow the cursor,

modify the measurement conditions through the up, down, right and left arrows, press the "Enter button"

to confirm exit.

Menu Setting: In the main menu mode, press "Settings button" enter the menu setting mode, select

"Measurement condition setting", you can modify the "Sample length", "Evaluation length", "Range",

"Filter", "Standard", " Parameters "," C (rmr) "," C (rpc) "," Rmr (rδc) "," Unit of measurement ".

Main Menu

Conditions Setting

3.4.2 System Setting

In main interface, long press setting to enter menu setting, choose system setting, enter the sub-menu.

In this menu, you can set: “Key Buz”, “Warning Buz”, “Power Save”, “Auto Off”, “Time Calibration”, “Low

Noise Test”, “Display Test”, “Remote Matching”, “Surface Type Selection”. Press enter key to exit.

3.4.3 Time Setting

Clock setting is always showed when first use, press left (right), up(down) to set the clock. When

finishing, press the enter key to exit.

If the time is wrong, adjust the clock as follows

：

1

Enter the main interface

The interface is the main interface. MR200 always shows this interface before and after the measuring.

Includes the main measurement parameters and conditions of the measurement information, such as

sample length, assessment of the length, range, filter and measurement units.

Содержание MR200
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды