background image

QDV-1000 Hardware installation:

 

 

1.  The QDV-1000 module comes already mounted onto a CH-559 metal plate.  The CH-559 mounts onto the 

QBC-5000 battery charger cover located above the amplifiers in the audio cabinet of the QX-5000 Audio 
system.  The QBC-5000 cover must be removed and the QDV-1000 and its plate is mounted onto the QBC-
5000 cover with the four 4-40 ¼” screws provided for the purpose.  The whole assembly is then mounted back 
into the audio cabinet over the battery charger.

 

2.  Locate the J8 header on the QIF-5000B. Align the key on the ribbon cable header from QDV-1000 (J2) with 

the opening of the J8 and plug the cable into the shrouded header. 

   

3.   Connect a wire from terminal TS1-1 on the QDV-1000 TS1 to QIF-5000B J4 terminal 1.  Also connect terminal 

TS1-2 on the QDV-1000 to QIF-5000B J4 terminal 2.

 IMPORTANT: This is required for all installations.

 

      4.  For single stage alarm system, place a 22 gauge shorting wire on pins 1 and 2 (of JP5) on the QIF-5000B.  

For a second stage system add a 3.9K ohm resistor between pins 1 and 2 (of JP5) on the QIF-5000B, refer to 
the QX-5000 manual.

 

 
 

 

 

   

QIF-5000A or QIF-5000B interface Module 

 

                      

 

 

 

LT-901 Rev.4 Aug 2006 

          Page 6 of 10 

Содержание QDV-1000













Отзывы: