Miranda PresStation Скачать руководство пользователя страница 5

Страница: 5 / 145

PresStation User Manual

Preface

Miranda Technologies Ltd

Page 5

To avoid injury or fire hazard, do not operate PresStation in an explosive
atmosphere.

Product Damage Precautions

8. Provide proper ventilation.

To prevent PresStation overheating, provide proper ventilation.

9. Do not operate with suspected failures.

If you suspect there is damage to PresStation, have it inspected by
qualified service personnel.

Certifications and Compliances

PresStation has CE approval and complies with the standards detailed in
EN50082-1:1992 and BS EN 60950:1992 Amd 3.

Scope of the User Manual

This User Manual includes all the information you will need to get started
using PresStation and using all the facilities available from the PresStation
control panel.

For technical, set-up and specific product information refer to the
publications listed below.

Associated Publications

Presmaster Integration Guide

Part No. 01234

Presmaster Automation Guide

Part No. 01235

Presmaster Configurator Manual

Part No. 02717

Presmaster User Manual

Part No. 01232

Imagestore User Manual

Part No. 02359

Содержание PresStation


















































































































































Результаты поиска

Содержание PresStation

Отзывы:

Бренды по названию

Популярные бренды

Miranda PresStation, Руководство пользователя

Результаты поиска

Содержание PresStation

Отзывы:

Бренды по названию

Популярные бренды