manualshive.com logo in svg

Miranda Kaleido-X, Руководство по установке

Поделиться
Скачать
Miranda Kaleido-X Скачать руководство пользователя страница 14

8

Kaleido-X (4RU) Installation

Ventilation

Ventilation

The Kaleido-X frame is cooled by ventilation fans. Fans are located in key positions within 
the frame.

Frame Cooling Fans

Primary ventilation for the cards installed in the frame is handled by eight fans located in a 
module on the left-hand side of the frame.

These fans draw air into the frame through a grille and filter in the front door, and exhaust it 
through the grate on the side of the frame.

Power Supply Cooling Fans

Each power supply has two fans located on the front of the supply.

In addition, there is a fan located on the rear panel directly behind the power supplies, 
beside the AC connectors.

IMPORTANT

The Kaleido-X requires a constant flow of cooling air during operation.
DO NOT OPERATE THE UNIT IF THE FRAME COOLING FANS ARE NOT 
WORKING.

To replace a defective fan, see 

Replacing a Defective Cooling Fan

, on page 25.

Cooling fan module

Содержание Kaleido-X












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды