manualshive.com logo in svg

Miranda DENSITE IRD-3101, Руководство по установке и эксплуатации

Поделиться
Скачать
Miranda DENSITE IRD-3101 Скачать руководство пользователя страница 12

GUIDE TO INSTALLATION AND OPERATION 
 

8

  |  IRD-3101 

3  Operation 

 

3.1  Control options 

 

The IRD-3101 can be controlled in two different ways: 

 

•

 

The local control panel and its push-buttons can be used to move through a menu of parameters and to adjust 
parameter values (see section 3.3). 

 

•

 

Miranda’s iControl system can be used to access the card’s operating parameters from a remote computer, using 
a convenient graphical user interface (GUI). (see section 3.4) 

 

3.2  Card-Edge Status LED 

 

The status monitor LED is located on the front card-edge of the IRD-3101, and is visible through the front access door 
of the DENSITÉ frame. The chart shows how the various error conditions that can be flagged on the IRD-3101 affect 
the LED status. 

•

 

If a cell in the chart is gray, the error condition cannot cause the LED to assume that status 

•

 

If more than one LED status is possible for a particular error condition, the status is configurable.  

 

See Section 3.4.16 for details. 

•

 

The factory default status is shown by a 

, and forced status by an

 X

  

 

The LED will always show the most severe detected error status that it is configured to display, and in the chart error 
severity increases from left to right, with green representing no error/disabled, and flashing red the most severe error.   
 

Alarm Name/Error Report 

Led Color 

Description 

Green 

Yellow 

Red 

Flashing 

Red 

Card booting 

  

X 

  

  

After power-up, the led becomes yellow until Linux 
is properly booted (takes about 40s) 

Hardware/System Failure 

  

  

  

X 

Major hardware or system failure.  In some cases, 
the error log will show the reason  

No Rear Detect 

  

 

 

X

 

As per densité  

No TS Input Signal 

  

  

 

  

No MPEG TS input detected 

TS Limit 

 

 

 

 

TS has more than 128 PIDs or more than 64 
programs or more than 1024 tables 

No Video Signal 

  

  

 

  

The MPEG TS input might be present, but no video 
signal is available for decode 

No Audio Signal 

  

 

 

  

The video may be present, but no audio stream is 
valid for decode 

No Reference Signal 

 

 

 

  

No reference signal is detected 

Reference Mismatch 

  

 

 

  

A reference mismatch is detected 

Program not synchronized 

 

 

 

  

The decoded video is not synced on PCRs 

Test Bars ON 

 

X

 

 

  

The card is in test mode with color bar activated 

 

If the LED is Flashing Yellow, it means that the card is selected for local control using the Densité frame’s control 
panel. See Section 3.3 for details. 

Содержание DENSITE IRD-3101

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды